搜索资源列表
ps2_keyboard_test
- FPGA通过ps2接收键盘数据，然后把接收到的字母A到Z键值转换相应的ASII码，通过串口发送到PC机上。需要接键盘，还要用调试助手，下载程序后，在键盘上按下一个键，比如A，则在PC调试助手上可看到A-FPGA received by ps2 keyboard data, and then received the letters A through Z keys to convert the corresponding ASII code, sent through the serial po
ScommTest
- 实现串口自动搜索；设置串口的数据位、停止位、波特率、检验位；能够通过串口发送、接收字符串-To achieve the automatic search of the serial port to set the serial data bits, stop bits, baud rate, parity bit can be sent through the serial port to receive the string
serialport
- 串口数据接收和发送，可以打开和关闭串口，可以自动发送也可以手动发送，可以设置延时时间，可以计数接收到和发送的数据位数-Serial port receive and send data, you can open and close the serial port, can also automatically send you can manually send, you can set the delay time, you can count received and sent data
mySerialPortTools
- qt写的串口通讯软件，可以实现串口发送，接收，功能完整-qt write serial communication software, serial port to send, receive, full-featured
NRF2401
- TX数据发送程序继续发送TXBUF的RX接收程序接收到的数据时，把从串口发送当前数据。波特率和校验，9600，N1。-TX data, send the program continue to send TxBuf the RX when the received data to receive the program put the current data sent from serial port. Baud rate and parity, 9600, N, 1.
U22SART
- stm32串口的调试，串口2发送数据串口1接收并在串口调试助手上显示-the stm32 serial debugging, serial 2 send data to serial port 1 receiver and displayed on the serial debugging aides
communication
- 在一块板上编写矩阵键盘扫描程序，当扫描到有键被按下时，将建通过串口发送出去，另一块板上单片机接收到串口发送来的键值后，将对应键值以0~F方式显示在数码管上。-A board to write the matrix keyboard scanner, when scanning to a key is pressed, will be built through the serial port to send out for an on-board microcontroller receives
STC-IRRXD
- 红外接收程序。适用于市场上用量最大的HT6121/6122及其兼容IC的编码。 对于用户码与User_code定义不同的遥控器，程序会将用户码一起从串口输出。 使用模拟串口发送监控显示编码，显示内容为ASCII码和中文。 本接收程序基于状态机的方式，占用CPU的时间非常少。 适用所有STC系列MCU。-Infrared receiver program. Applicable amount of market largest HT6121/6122 and
YB0F2
- 经过红外接收头解调后单片机接收到的高低电平是和遥控器发射时是相反的一个过程 * 兼容 1T-12T单片机中断方式红外接收数据，并通过串口发送 程序编辑： lbq691477940 22/07/20-The MCU receives the infrared receiver demodulation to low launch and remote control is the opposite of a process* Compatible 1T-12T microcontrolle
mega16
- iccavr开发c语言源码 mega16单片机的模拟舵机控制程序 内部包含串口发送和接收命令用于和上位机进行调试舵机-mega16 microcontroller iccavr development of c language source analog servo control within the program contains the serial port to send and receive commands for the host computer to debug the
control-Robot
- 单个按钮控制机器人小车运动。通过串口发送数据，单片机接收数据完成相应动作。-Single button to control the robot car movement. Send data through the serial port, the microcontroller receives data to complete the appropriate action.
GPS-data-collection
- GPS数据的采集，串口发送和接收，显示在LCD-GPS data acquisition, serial port to send and receive, displayed on the LCD
main
- KEIL编写 串口的接收与发送程序 51单片机-KEIL to write a serial program 51 microcontroller
51-Serial-Communication
- 51 单片机 基于keil软件的 串口通讯 接收发送程序-51 single-chip based on the keil software serial communication receiver to send a program
RC5
- * 程序描述:红外遥控RC5码解码程序,经串口发送 * 目标cpu:lpc932 * 晶振:11.0592M * 硬件描述:一体化接收头接P20.指示LED接P26-* Program Descr iption: Infrared remote control RC5 code decoding process, sent through the serial port* target CPU: lpc932* crystal: 11.0592M* Hardware Descr ip
Serial-Print
- 本程序实现了以下功能： 单片机上电后等待从上位机串口发送来的命令，同时在数码管的前四位以十进制 显示 AD采集来的数值。 1）当收到以十六进制发送来的01后，向上位机发送字符串“Turn off ad!”,同时间隔 一秒读取AD的值，然后把AD转换过来的数表示成实际电压值（浮点数），并且从串口发 送给上位机，形式如“The voltage is 3.398438V”发送周期也是一秒一次。 2）当收到02时，向上位机发送“Turn off ad!”并停止发送电压值 3）
51tx
- 单片机串行口发送/接收程序，每接收到字节即发送出去 和微机相接后键入的字符回显示在屏幕上. -Serial port to send/receive program, each receives the bytes sent and the computer phase after typed characters back to be displayed on the screen.
UART
- //DMAVR-128的USART串口发送与接收数据示例程序，采用串口1，发送和接收都是中断的方式 //先发送200个FF，然后单片机处于接收状态，接收数据显示在数码管上，电脑发送的数据格式如09，16进制形式-//DMAVR-128 USART serial port to send and receive data sample program using the serial port to send and receive are interrupted// 200 sends th
chuank
- 单片机控制的串口程序，模拟串口发送和接收。-Serial program, microprocessor controlled analog serial port to send and receive.
HS0038
- 通过外部中断来控制红外线的接收，再通过串口发送数据-External interrupt to control infrared receiver, and then send data through the serial port