搜索资源列表
uart
- 简单的串口收发数据，实现当在串口助手发送数据通过终端接收，然后返回给终端-Simple serial data transceiver to achieve When the serial Assistant to send data received by the terminal, and then returned to the terminal
Zstack-ADXL345
- 基于zstack协议栈的adxl345传感器通信代码，协调器建立网路后终端自动加入，将传感器数据发送给协调器，协调器通过串口将数据传输给PC。 使用IAR编程环境，文件夹内已附带协议栈，打开project-zstack-Samples-CC2530-ADXL345-CC2350DB下的TestC.eww可直接运行-Based the ADXL345 sensor communication code zstack protocol stack, coordinator create a n
Zstack-HMC5883L
- 基于zstack协议栈的HMC5883L传感器通信代码，协调器建立网路后终端自动加入，将传感器数据发送给协调器，协调器通过串口将数据传输给PC。 使用IAR编程环境，文件夹内已附带协议栈，打开project-zstack-Samples-CC2530-HMC5883-CC2350DB下的TestC.eww可直接运行-HMC5883L sensor communication based on zstack protocol stack code, the coordinator automa
MODEMCOMM
- 本例利用MSCOMM控件，通过串口发送AT指令来操作MODEM,使两台计算机通过公用电话网进行数据传送-This case, use the MSComm control through the serial port to send AT commands to operate MODEM, two computers for data transmission via the public telephone network
linux
- linux下的串口通信程序详解,给出测试程序来理解linux下的串口操作流程，例程receive.c用来接收从串口发来的数据，而例程send.c用来发送数据到串口。二者成功建立串口连接后，串口接收端会收到串口发送端发来的字符串数据“Hello，this is a Serial Port test!”。-serial communication program under linux Detailed test procedure is given to understand that under
C8051f005.-Txt
- C8051f005 单片机编程 设计系统初始化，AD采样，串口发送和接收数据-C8051f005 Modify a the AD sampling part of the program,
sci_loopback_interrupts
- 利用DSP2812串口发送4通道数据，上位机4通道接受并显示-4-channel, the PC accepts and displays using DSP2812 serial port to send the 4-channel data
SerialportSample(2)
- 一个C#编写的串口调试助手工具，可以接收串口发送的数据，代码注释详细，串口开发初学朋友值得一看-A C# prepared by the serial debugging assistant tool, you can receive serial data sent detailed source notes, serial development worth beginner friend
bmp085_stm32_usart
- BMP085气温气压模块，stm32f103控制，采集到的数据通过串口发送到pc机上显示-BMP085 Temperature Pressure Module, stm32f103 control, data collected through the serial port to pc machine on display
74HC165aUART_ARM
- 在Keil环境下编写的STM32代码，用来读取74HC165的数据并通过STM32串口发送（至蓝牙/SIM/PC等），波特率115200。-In the Keil environment prepared STM32 code, used to read the data and 74HC165 serial port to send via STM32 (to Bluetooth/SIM/PC, etc.), baud rate 115200.
iar_for51_uart
- iar for 51 的串口发送例程，数据发送波特率控制模块-iar for 51 serial send routine, the data transmission baud rate control module
adc
- 将ADC对输入端口电压的转换结果按转换数据和对应的模拟电压的形式通过串口发送到PC机屏幕上显示-The ADC input port voltage conversion results by converting data and the corresponding analog voltage sent to the PC via the serial port on the screen
FFT
- 可以在processing中运行的FFT，利用串口发送采集的数据，然后交给processing处理显示波形。-You can run the processing FFT, using the serial port to send the collected data, and then to processing processing and display waveforms.
serialport_test
- 串口测试，测试串口接收到的数据，串口发送所需的数据-Serial tests to receive serial data from serial port to send the required data
uartfifo
- 将产生的数据存入FIFO中并由串口发送出去。-The resulting data into the FIFO by the serial port to send out.
IR2PC
- 定时器模拟串口红外接收数据，并通过标准串口发送到电脑-Timer analog serial infrared receiver data, and sent to the PC through a standard serial port
IR_Remote_Control_winamp
- 单片机端接受红外遥控并通过串口发送至电脑端程序，电脑端程序获得数据后控制Winamp的上一首、下一首、音量大小等。串口使用4800波特率，8字节，一位停止位，无校验，单片机使用12Mhz晶振，VB6.0，win7 32bit下测试通过。-Receiving infrared remote control MCU side and sent to the PC via the serial port procedures, computer terminal procedure for obtai
3
- 实现视频字符叠加系统数据的串口发送和当前温度检测和显示-Achieve video character overlay system serial data transmission and the current temperature detection and display
20130607UART
- 读取温度传感器DS18B20数据并通过串口发送到上位机。程序开发是基于altera 的EP2C8Q208芯片。-Read the temperature sensor DS18B20 data and sent it to the host computer via the serial port. The program development is based on the the altera s cyclone II device :EP2C8Q208.
10_ps2_keyboard_test
- FPGA通过ps2接收键盘数据，然后把接收到的字母A到Z键值转换相应的ASII码，通过串口发送到PC机上。 实验时，需要接键盘，还要用调试助手，下载程序后，在键盘上按下一个键，比如A，则在PC调试助手上可看到A -Through FPGA receive the ps2 keyboard data, and then receive the letters from A to Z key value into corresponding ASII code, through A seri