搜索资源列表
STM32-8-channel-ADCPTFT
- 8通道ADC+TFT+串口发送,包括针对8通道ADC数据进行显示及发送处理的各种要求-8 channel ADC+TFT+ serial port to send, including a variety of display and transmit processing for 8 channel ADC data requirements
F340_uart
- 实现8051F340的数据采集通过串口发送-for8051f340 datalogging and send by serial port
sending-and-receiving-data
- 这个是关于51单片机的小程序，是关于串口发送与接收数据的应用- This is about 51 single small program, is sending and receiving data on the serial application
LPC2134_WR_FM25L04
- 通过串口0，波特率9600 发送十六进制数,连续写入FM25L04的前30个地址，且最后地址的数据始终是串口发送的第三个数,再读出，发送到串口软件上 01 00 7F 10 04 05 06 07-0 through the serial port, baud rate 9600 to send the hexadecimal number, sequential write address FM25L04 before 30, and the last address data is
temp
- NRF24L01设置为32帧数据收发 下位机接收到来自目标温度单片机发过来的温度信号之后， 进行判断接收到的温度信号有没有传递错误 若头三个字节分别为0x55，0xaa，0xcc，则说明信息传递没有错误 其中串口发送到PC上位机的数据格式为 8路无线温度实时监控系统.带proteus仿真。第0,1,2字节分别为0x55，0xaa，0xcc 作用为判断数据传送有没有出错，若PC 上位机接收到这三个字节有其中一个字节不相同，则归为数据传送出错，不进行处理-After N
51Comm
- 单片机将采集到的数据处理后，通过串口发送出去-SCM will handle the collected data, sent through the serial port
01.PCTOPCMSComm
- 实现电脑和电脑之间通过串口进行数据发送个接受-Achieved between the computer and the computer sends data via a serial port to accept
RS232Thread
- 多功能串口通讯程序,可以采用多种格式将数据集通过串口发送给设备.使用灵活方便-Multifunction serial communication program, you can use a variety of formats the data set is sent to the device through the serial port using flexible
U0C0
- 串口发送队列，确保发送数据的正确性，不会丢失数据-Serial transmit queue
SRM7
- 观测单片机上传数据，通过单片机串口发送一组数据，在上位机界面上画出相应图形-Observations microcontroller upload data, a set of data sent via the serial port MCU, draw the appropriate graphics on the PC interface
ADPUARTPDPRAM
- ad7606采集信号数据存入双口ram再通过串口发送出去。- ad7606 collected signal data stored in the dual port ram and then sent through the serial port.
ADCPUSART
- ADC+USART STM32开发板的AD转换以及串口通信例程，AD采集的数据通过串口发送到PC机-STM32 development board AD conversion and serial communication routines, AD data through the serial port to send to the PC machine
OV7670_4
- 在STM32平台上实现JPEG编码，摄像头为OV7670，可以通过串口发送到PC端，数据保存为.jpg格式即可显示。-Realization of JPEG encoded on STM32 platform, camera for OV7670, can be sent to the PC via the serial port and save data. Jpg format to display.
run-LED
- 旋转LED平面字体测试程序 用单片机的串行口发送数据给3个595 并行驱动LED 采用无线供电方式以及性能较好的RF370电机,在5V供电下 显示的效果非常好.电机速度也够快 够安静. 只为简单的理解显示的原理，利用人眼视觉暂存，用电机旋转做列扫描， 每送一列数据延时 再送下一列数据，原理比较简单，跟点阵显示差不多。-Rotating LED flat font test program with single-chip microcomputer serial port to s
uart_send
- 单片机串口发送实验已实现，可正常使用,可往单片机及PC发送数据-Send microcontroller serial experiments have achieved normal use, you can send data to the microcontroller and PC
YB0F2
- 经过红外接收头解调后单片机接收到的高低电平是和遥控器发射时是相反的一个过程* 兼容 1T-12T单片机中断方式红外接收数据，并通过串口发送程序编辑： lbq691477940 22/07/20-The MCU receives the infrared receiver demodulation to low launch and remote control is the opposite of a process* Compatible 1T-12T microcontroller inte
Mscomm-1.0
- 串口接收数据，能接收和发送16进制，接收的数据能转换层十进制数同时提取，协议是485的-Serial port receives the data, can send and receive hexadecimal, the received data layer can convert decimal number extraction at the same time, the protocol is 485
motor-control
- 电机正反转程序，通过在上位机界面上点击正转/反转，通过串口将数据发送出去，在下位机这边电机会执行相应的指令-Motor reversing procedures, by clicking on the host computer interface forward/reverse, through the serial port to send data out, the next bit machine to perform the appropriate side of the motor
chuankou01
- 串口接收数据发送数据 单片机采用430单片机-Serial receive data send data SCM 430 SCM
version15
- 通过选择串口发送控制信息和接收返回数据，运用多线程来与硬件设备交互，并将接收的数据显示出来。-Through the selection of the serial port to send control information and receives the returned data, the use of multiple threads to interact with hardware devices, and the received data is displayed.