搜索资源列表
bobo
- 用Labview写的串口上位机,可实时显示波形,没有通信协议,直接用单片机发送要显示的数据就可以了-Written using Labview serial PC, real-time waveform display, there is no communication protocol, the direct use of the microcontroller sends the data to be displayed can be
Meteorological-monitoring-system
- 气象上位机监控系统,通过串口通讯接收下位机采集到的数据,以波形形式显示,智能报警,实时储存数据的功能-Meteorological PC monitoring system, through serial communication receive under the collected data, in wave form display, intelligent alarm, real-time data storage capabilities
test01
- 利用labvIEW实现串口接收数据并实时显示波形的简单功能。-Use labvIEW Serial receive data and real-time waveform display a simple function.
SensorDataCollection-
- 波形显示程序,读取串口数据,并以波形的形式显示出来,串口数据的传输频率为100Hz,数据格式在代码中可以看到-Waveform display program, read the serial data, and the form of the waveform display, serial data transmission frequency is 100Hz, the data format can be seen in the code
VBwaveform-analysis
- 基于VB环境下的VB嵌入式串口通讯波形分析显示软件,适合新手学习-Embedded VB serial communication waveform analysis software
vhdl
- 实现信号发生器的vhdl教学代码,提供了串口的功能和发生波形的功能,-Realization of the signal generator vhdl code for teaching
1025wd01
- 通过串口把读到的温度 用波形显示 针对于仪器仪表温度测量-Through the serial port to read the temperature with a waveform display for temperature measurement in instrumentation
SCI232aPWM
- Fresscale 串口232以及PWM波形产生-Fresscale port 232 and a PWM waveform generation
MCU
- 单片机的9个实验程序,主要是通过单片机的串口输出数据,方波波形,led灯点亮等-MCU 9 experimental procedure, mainly through the serial data output of MCU, square wave, LED lights etc..
Ultrasonic-Ranging-PC-display
- 通过软件Labview编写前面板和程序框图,通过该面板实现计算机与单片机的串口通信。设置好通信端口,波特率等参数后,超声波传感器检测距离,由单片机进行处理,通过串口将检测的距离输入到计算机,以波形图表显示实时距离,并进行实时存储。-Written on the front panel and block diagram software Labview, Computer and MCU serial communication through the panel. After setting
AD9850-modulation-Data
- AD9850/AD9851模块是采用ADI应用最广泛的DDS(AD9850和AD9851)制作的模块。ADI的性能就不用多说了。模块主要参考AD9850和AD9851的资料做的。 主要功能特点: * 模块能够输出正弦波和方波,2个正弦波和2个方波输出。 AD9850: 0-40MHz AD9851: 0-70MHz 频率在20-30MHz后谐波越来越大,波形会越来越不干净。 方波: 0-1MHz * 采用70MHz的低通滤波器,使波形的SN比更好 * 并口
Uart
- 单片机串口数据采集,主要是测电压,并在上位机上显示出波形-Microcontroller serial data acquisition, mainly voltage measurement
Labview-serial-visa
- Labview的VISA串口通信,能够向下位机读写数据,并能显示波形,调试通过。-Labview VISA serial communication, can read and write data to the PC, and can display the waveform, debugging through.
serial-datalog
- 基于labview的串口数据采集显示.可以通过把串口传来的8位数据转换成波形显示。可以自制数据采集器-Labview-based serial data acquisition and display
boxing
- 波形程序,通过串口语虚拟示波器连接可以看到正弦波 处理器MC9S12XS128 包含了crc16校验,适合串口通信 欢迎交流!-Waveform program, through the serial port connection can see the phrase virtual oscilloscope sine processor MC9S12XS128 contains crc16 checksum for serial communication exchange we
show-wave-by-serial
- 通过串口显示传来的数据波形,最大速率传输,没有校验-show wave by serial
serial
- 用C#编写的串口助手,源码,并有波形显示,保存数据;自动识别串口,二进制,十进制,16进制发送;等功能。-Written in C# serial assistant, source, and waveform display, save the data automatically identify serial, binary, decimal, hexadecimal sent other functions.
Pat2000
- VC++编写的串口读写例子程序,可以显示两导波形-VC++ prepared by the serial read and write example program that can display two waveforms guide
daima
- 下载代码后,利用转串口模块,在串口猎人中发码区选HEX,波特率自己选择合适的,在高级收码中,来源选项选择提取每一帧,帧尾前打勾,帧长限制为2,然后启动高级收码,启动示波器,即可看到波形了-After downloading the code, the use to serial module, serial code area selected hunters medium HEX, choose the appropriate baud rate, the senior received co
MPU6050_DMP_Demo
- MPU6050测试程序,用AVR Atmega16写的。使用串口查看波形-MPU6050 test program, using AVR Atmega16 written. Use the serial port to view waveforms