搜索资源列表
RS_232_FULIYE
- vc 6.0下使用MSComm控件进行串口通讯,可进行相应的通讯设置,显示串口数据并动态绘制波形图/曲线图,使用快速傅里叶变换将时域信号的串口数据转换为频域值,并动态显示。代码内有注释-vc 6.0 control for the use of MSComm serial communications, the communications can be set, indicating the serial data and dynamic mapping wave/curve, the use
uart
- 用ALTERA的芯片做的多串口代码,内部做了3个通用串口,适合51 ARM等CPU,有完整的ALTERA工程和仿真波形-uart FOR ALTERA
ourdev_552702
- 通过串口将TXT文件中的数据读取出来,并显示波形-Through the serial port data in the TXT file to read out and display the waveform
ECG1
- 基于MATLAB的串口收发程序,可以完成数据的接受,波形显示,存储,基于小波理论的消噪处理,对于学习MATLAB的GUI编程很有好处!-Serial transceiver based on MATLAB program to complete the data received, waveform display, storage, de-noising based on wavelet theory, processing, MATLAB-GUI programming for learni
COMM
- VB嵌入式串口通讯波形分析显示软件-VB Embedded Serial Communication waveform analysis display software
SerialPortUtility
- VB编写的串口通讯源代码,同时能显示串口波形。 -VB source code written in serial communication, serial port at the same time can display the waveform.
12864lcd
- 单片机的利用12864液晶尽性波形描绘程序,采用c语言编写,串口通信。-12864 LCD MCU to make use of wave described procedures, using c language, serial communications.
extend
- MSP430 的程序,可以进行电压采集并通过串口与另一个单片机进行串行通信,另一台单片机将波形显示在示波器上-MSP430 process, voltage can be collected and microcontroller through the serial port with another serial communication, the other single chip waveform displayed on the oscilloscope
Serial_Oscilloscope_MSP430F149
- 用MSP430F149做的一个示波器,用Timer A定时触发AD转换,串口发送给电脑,最高采样频率100ksps左右,LABVIEW的visa接受和显示波形并可以控制时间轴和波形放大轴。-oscilloscope with MSP430F149 , starting with Timer A to trigger AD converter, send to the computer with RS232, the maximum sampling frequency 100ksps aroun
Vdfsdfs
- 串口示波器功能,测试并记录 显示波形 显示峰值-Serial oscilloscope function, test and record the waveform display
SerialCommunication
- LabView的串口通信程序,上位机通过串口得到的数据可显示在波形面板上-LabView serial communication program, the data which get from serial can be displayed in the waveform panel
vb
- VB串口源代码,可以显示波形,绝对有用,特地分享-VB serial port source code, you can display the waveform, the absolute useful, specially to share
Display
- 示波器显示 接受串口数据 波形幅值 周期 大小可以调整-Oscilloscope display to accept serial data
C-sharp_PC2MCU_Draw-master
- 可以显示串口收上来的数据和波形,也可以显示摄像头数据(Can display data collected from the serial port and waveform)
test1
- 新建VI(test1\serial_communication.vi),运用仪器I/O\串口\VISA配置、读取、关闭、字节数、清空缓冲 等函数,编制测距传感器的串口通讯接口VI;通过波形图表显示连续读取的测距-时间曲线,并将有效测量范 围外的数据滤除。(New VI (test1\serial_communication.vi), using the instrument I/O\, serial port, \VISA configuration, read, close, bytes,
ECGDATAV6test1
- 串口发上来数据,前三个字节为枕头,四个字节代表一个数据。一共15字节,把数据存到txt,运行画出波形(The serial port sends the data. The first three bytes are the pillows, and the four bytes represent one data. A total of 15 bytes, the data stored in the txt, running draw a waveform)
mycom
- 使用pyqt 实现windows下串口通信,包括串口选择配置,数据收发等。当然也可以加入pygraph实现波形显示,可做为上位机程序的参考(Using pyqt to achieve windows serial communication, including serial selection, configuration, data transceiver. Of course, you can also join the pygraph to achieve waveform displa
等精度数字频率计
- 可以测量1HZ-150MHZ矩形波(其他波形需整形后输入)信号,误差<0.01%,串口输出NC和NX值。(1HZ-150MHZ square wave can be measured (other waveform needs to be shaped after the input) signal, error <0.01%, serial output NC and NX values.)
温度波形显示
- labview上位机波形显示并保存数据,下位机通过串口通信将数据发送到上位机,数据显示并保存在TXT文件里。附带51测试程序。(LabVIEW host computer waveform display and save data, the lower computer through serial communication to send data to the host computer, data display and save in the TXT file. Comes with
chuankou
- 基于LABVIEW的串口程序,可以更改波特率等功能,具有波形图像(This program is about serial port based on LABVIEW,which can change baud rate and other functions, with waveform images screening and so on.)