搜索资源列表
F2812_SCI02 PC机串口调试助手
- F2812 SCI与PC机串口调试助手以收发中断方式实现收发数据。(CCS3.3开发环境) 功能:使用SCIA模块和PC机进行串口通信,等待PC机上的串口调试软件向DSP发送"hellodsp",DSP接收到上位机发送的数据之后,将这些数据发回PC机,显示在串口调试软件中。 说 明:本实验中SCIA模块的发送和接收采用中断方式实现,空闲线模式波特率为19200,通信数据格式为1位停止位,8位数据位,无校验位-F2812 SCI and the PC serial port r
uart1
- stc的12c5a60s2单片机的单独波特率UART串口通信-stc' s 12c5a60s2 separate microcontroller UART baud rate serial communication
C8051F310
- C8051F310单片机与计算机的串口通信的例程,可减少系统开发时间:单片机接收计算机发过来的字符串,回发字符串.发送期间中断控制LED灯闪烁,采用外部晶振22.1184MHz 使用定时器1,方式2产生波特率-C8051F310 MCU and the computer
serial
- -- 本模块的功能是验证实现和PC机进行基本的串口通信的功能。需要在 --PC机上安装一个串口调试工具来验证程序的功能。 -- 程序实现了一个收发一帧10个bit(即无奇偶校验位)的串口控 --制器,10个bit是1位起始位,8个数据位,1个结束 --位。串口的波特律由程序中定义的div_par参数决定,更改该参数可以实 --现相应的波特率。程序当前设定的div_par 的值是0x104,对应的波特率是 --9600。用一个8倍波特率的时钟将发送或接受每一位bit的周期时
uart
- 430通信程序,通过配置430URAT模块实现波特率9600 2400 15200串口通信-430 Communication Program, through the configuration 430URAT Module 9600 2400 15200 baud rate serial communication
ComMaster
- 串口通信,可自由设置com口,波特率,传输位数,传输模式字符,或十六进制-Serial communications, are free to set the com port, baud rate, transmission median transfer mode character, or hexadecimal
UART_SUCCESS
- 实现FPGA和上位机的串口通信,里面由波特率发生器,移位寄存器,计数器,detecter,switch,switch_bus等功能块综合而成。-FPGA implementation and the host computer' s serial communication, which by the baud rate generator, shift register, counters, detecter, switch, switch_bus such as function bl
COM_MCUPC
- 单片机-PC 串口通信(Altium Designer Winter 09工程和原程序) (2010山东大学威海分校电子设计大赛F题)PC 机侧可用现有通信软件(如串口调试助手),单片机接一位数码管,实现 PC 发送数据,单片机接收显示,并回送给 PC 机。 *单片机系统需对 PC 机下发串口数据的波特率能够自侦测 *PC 机下发数据前循环发送 0Xff 作为侦测标识 -SCM-PC serial communication (Altium Designer Winter
C8051F-MCU-serial-communicat
- C8051F单片机与PC串口通信, 能实现各种C8051单片机的串口通信,9600波特率,232协议-C8051F MCU and PC serial communication
kehshechenxu
- 编制一全双工UART电路,通过试验箱MAX202E转换成RS232电平,与计算机进行通讯实验,设置8个按键,按键值为ASIC码“1”~“8”,通过串口发送给计算机,在计算机上显示键值,同时在数码管最高位显示;计算机可发送“0”~“F”的ASIC码,FPGA接收后在数码管低位显示0~F。通过按键可设置波特率。 要求:波特率为三种 1200、2400、9600,由1个按键选择,3个LED分别指示; 数据格式为1位起始位、8位数据位和一位停止位; 上位计算机发送接收软件可使用
SerialPort
- 读取注册表获取串口号,进行串口通信,通过软件界面可以设置波特率、数据位等参数(It is a software used to communicate with serial port. It is coded on QtCreator with a serialport class. The software can check the regedit and get the Com port. Users can set Baud rate, data bits and so on.)
频率接收
- STM32F103与FPGA的串口通信,波特率4800,采用单向通信的方法。(Serial communication between STM32F103 and FPGA)
串口保存文件1
- 串口通信 波特率9600 数据位8 停止位1(Serial communication)
uart_ip
- 实现串口通信模块设置,包括频率分频、波特率产生、接口时序要求(Implementation of serial communication module settings, including frequency division, baud rate generation, interface timing requirements)
串行通信
- 计算机与单片机之间实现串行通信,10位异步通信,波特率1200,采用定时器1产生,实现计算机串口调试助手与单片机之间的双向通信;(The serial communication between computer and MCU is achieved. Asynchronous communication with 10 bits and baud rate of 1200 are generated by timer 1, which realizes two-way communicati
串口数据刷新
- 实现通信助手的功能,刷新显示,波特率可调节,USB通信,可以用来做USB串口的传感器通信(Realizing the function of the communication assistant)
UART9600&PWM
- 程序编写实现了UART串口通信的收发功能,设计波特率调整,还有50HZ的PWM波(The program is programmed to realize the transceiver function of UART serial port communication, design baud rate adjustment, and 50HZ PWM wave.)
中级篇03:UART,波特率115200与PC通信
- 本程序实现FPGA的串口通信功能,可以进行数字字符等的发送,波特率为115200(This program implements the serial communication function of the FPGA, and can transmit digital characters, etc., and the baud rate is 115200.)
fpga 实现 串口通信
- 串口通信,可以任意修改波特率, 亲自验证过,通信可靠,采用verilog HDL语言编写,代码包含注解
基于STM32的串口通信下载软件
- 一款适用于ARM的串口通信下载软件,可以调整波特率等参数,并支持查看收发数据。