搜索资源列表
bijindianji
- 单片机控制步进电机正反转,还可以控制步进电机速度-SCM stepper motor control, can control the stepper motor speed
memb
- 因单片机的ram非常有限,本人在实际的工作中发现在编写单片机程序时能使用动态内存分配将对程序结构和提高程序复杂度有很大的帮助,但是编写动态内存分配代码因ram有限又不适宜采用动态链表的方式来管理内存,采用固定分配块的方式又不能充分利用单片机的ram(有时候一个字节都很重要啊),为此想出这个在速度和ram使用效率折中的办法(因为在使用动态内存的地方往往速度要求不是很高)。 本代码是采用C语言编写,可以在任何可编译C语言的工具上编译。 如果你在使用中发现任何的bug,或者对单片机
PT2272
- 单片机模拟PT2272解码,振荡电PT2262/1.2M=PT2272/200K组合,解码速度快,在中断读取数据,不占用CPU时间.-Microcontroller analog the PT2272 decoding, oscillating electric PT2262/1.2M = PT2272/200K combination, decoding speed, interrupt read data, not the CPU time.
MCUdataprocess
- 基于单片机的多数据处理方法,适合各种不同的精度和速度的首选平台-MCU based multiple data processing method, suitable for different kinds of precision and speed of the platform of choice
MCUdata
- 单片机平台多种数据处理方法,适合不同种精度及速度的平台选择-MCU based multiple data processing method, suitable for different kinds of precision and speed of the platform of choice
shuju
- 数据处理,单片机平台多种数据处理方法,适合不同种精度及速度的平台选择-data processing,MCU based multiple data processing method, suitable for different kinds of precision and speed of the platform of choice
Ch6
- PIC单片机,基于同步法对直流电机大范围内变化的速度进行测量-The PIC microcontroller DC motor speed system development
Temperature-data-acquisition-system
- 用PIC中档单片机集成的A/D模块,采集LM35输出的模拟温度值,采样速度为2Hz。然后将10位的A/D转换结果分为高低两个字节(高字节8位、低字节2位),通过USART模块的异步模式传到PC机上。通信方式设定为波特率9600、帧格式为8位数据位、无校验位、1位停止位。-Integrated with a mid-range PIC microcontroller A/D module, collecting the the LM35 output of analog temperature v
freescale0720
- 能跑的智能小车程序,xs128单片机上实验成功,速度在3m/s左右吧。-Able to run smart car program, xs128 microcontroller on the experiment is successful, the speed is probably about 3m/s.
motor-control-of-AT89C51
- 利用51单片机实现对一个四相步进电机的控制和相应的数据显示。包括四相电机的启动和停止、控制正转和反转并显示其实际旋转方向及相应的速度等级。-51 single-chip implementation of a four-phase stepper motor control and data display. Including the start and stop of the four-phase motor control forward and reverse, and displays
lcd1602-motor
- 51单片机的步进电机控制,lcd1602显示电机转动方向及转速,用矩阵键盘调整方向及速度,包含c源码及proteus仿真-The 51 SCM stepper motor control, lcd1602 display motor rotation direction and speed, with a matrix keyboard to adjust the direction and speed, including c source and proteus simulation
DS18B20_Test1_STC12LE5A16S2
- STC12LE5A16S2为单指令周期高速单片机,使用原来51单片机的DS18B20程序必需降低速度才能工作或者增加延时也可以-DS18B20 procedures necessary to reduce speed to work. STC12LE5A16S2 as a single instruction cycle high-speed microcontroller, using the original 51 MCU or increase the delay.
dianjicesu
- 51单片机 键盘输入控制直流电机速度 ,有实时转速检测,带中文液晶显示。-51 the SCM keyboard input control DC motor speed, real-time speed detection with Chinese liquid crystal display.
Serial-port-data-acquisition-system-
- 本系统利用单片机通过串口和数字化的温度传感器18b20对温度进行采集和监控,通过串口通信可以将采集的温度数据传给电脑,利用电脑进行数据处理和显示,包括保存和回放数据,回放数据速度可进行调整。-The system microcontroller through serial port and the digital temperature sensor
pll
- 430单片机的锁相环技术,通过调节锁相环的倍频系数来调节单片机运行速度-The phase-locked loop technology 430 singlechip, through the multiplier factor regulating phase-locked loop to regulate the microcontroller running speed
bujin
- 51单片机控制步进电机的正反转,可以通过参数调节转动速度-51 MCU control stepper motor positive inversion, can be by adjusting the parameters of rotational speed
zhinengdianzishuye-sheji-
- 利用单片机设计并制作一个智能化的液体点滴速度监测与控制装置。该装置由水滴速度测试系统、水速控制系统、气泡空液阻塞检测系统,电源异常检测系统,显示滴速装置、故障处理系统,报警系统等系统组成。应用光透射原理监测滴速,利用控制步进电动机的转速来控制点滴速度,利用红外二极管监测液面高度,利用压力传感器检测导管堵塞,利用超声传感器气泡。点滴速度可用键盘来设定同时在水到达警戒线以下时能发出报警信号。-The use of single-chip design and production of an int
PID
- 比较典型的PID处理程序,在使用单片机作为控制cpu时,请稍作简化,具体的PID参数必须由具体对象通过实验确定。由于单片机的处理速度和ram资源的限制,一般不采用浮点数运算,而将所有参数全部用整数,运算-Typical PID handler, use the microcontroller as control cpu, some simplification, the the specific PID parameters must be experimentally determined
DC-motor-control
- 直流电机控制,内容是利用XC866单片机设计完成小功率直流电机的速度控制,设有按键,并利用LCD进行显示-The DC motor control, XC866 microcontroller design small power DC motor speed control has buttons and LCD display
bujin
- 使用51单片机驱动步进电机的完整的工程,可以直接使用的,控制速度可调-The use of 51 single-chip stepper motor driver complete project, can be used directly, control the speed adjustable