搜索资源列表
gpioKeyInputLedOutput
- STM32的GPIO输入输出，也就是读入按键值，然后使相应的灯点亮。-STM32 of the GPIO inputs and outputs, which is read into the key value, and then make the corresponding lamp lights up.
avr
- 用avr做的数字示波器，四个按键可调控频率和幅值。-Avr to do with the digital oscilloscope, the four buttons can control the frequency and amplitude.
Infrared-remote-control
- 通过红外遥控器对继电器喇叭控制，并在液晶显示按键值-Infrared remote control on the relay through the speaker control, and key value in the liquid crystal display
hongwai1602
- 基于89s52的红外遥控实现按键值并与1602显示，也可以改为与led显示-89s52-based infrared remote control to achieve key value and with the 1602 show can also be changed with the led display
WCE_SPI_Driver
- WinCE下的SPI驱动，该驱动从外部按键芯片处读会按键值。-SPI driver under WinCE, the drive key from the outside at the time the chip will be key values.
BPlusTree
- B+树实现的完全代码。B+树定义文件，本程序实行一个简单的B+树 (1) 一个v阶的B+树由根结点、内部结点和叶子结点组成。 (2) 根结点可以是叶子结点，也可以是有两个或更多子树的内部结点。 (3) 每个内部结点包含v - 2v个键。如果一个内部结点包含k个键，则有且只有k+1个指向子树的指针。 (4) 叶子结点总是在树的同一层上。 (5) 如果叶子结点是主索引，它包含一组按键值排序的记录；如果叶子结点是从索引，它包含一组短记录，每个短记录包含一个键以及指向实际记录的
MyKey
- 键盘按键获取,Virtual C++6.0所写,告诉你如何在自己的程序中获取键盘的按键值-Keyboard access, Virtual C++6.0 written, to tell you how to program your own keyboard key values to obtain
P05_LED_Key_Music
- 16位凌阳单片机按键播放音乐并显示按键值在数码管上-Sunplus 16-bit microcontroller button to play music and display the key value in the digital tube
P05_Led_Show_Key
- P05_Led_Show_Key 按键值循环显示在数码管上程序-P05_Led_Show_Key key value in the digital control loop shown on the program
key_isr
- 使用sonix芯片,扫描按键,在数码管上显示相应的按键值,使用中断的方式去读取出按键的数值-Using sonix chips, scan button, the digital value of the corresponding button on the display, use the interrupt key way to read out the values
uCOSnew
- 在ARM教学开发板上实现简单的按键控制，并且使得LED灯能够闪现相印的按键值-Teaching in the ARM development board to achieve a simple button control, and makes the LED light to flash of India' s key value
tm1637
- TM1637所有显示寄存器地址全部写满数据0xff，并开显示，然后再读按键值。-TM1637 all filled with all display data register address 0xff, and the open display, then read key value.
rf-remote-control
- 射频遥控器的控制软件，主要就是学习一个码，然后把这个码和按键值发送给主控机-RF remote control software, key is to learn a code, then the code and the key value is sent to the host computer
TX_SCI
- 简单的串口程序,根据矩阵键盘的输入从串口输出按键值 (0-F)-Simple serial program, according to the input matrix keyboard key value from the serial output (0-F)
tongxin
- 实现两个实验台之间的串行通讯。发送方读入按键值，并发送给接收方，接收方收到数据后在LED上显示。-Achievement of the two serial communication between the laboratory bench. Read key value of the sender, and sent to the receiver, the receiver receives data on the LED display.
Digital-pipe-display-experiment
- 矩阵式键盘按键值的数码管显示实验,定时器0的中断服务子程序，进行键盘扫描，判断键位-Keyboard key value matrix LED display experiment, the timer 0 interrupt service routine, the keyboard scan to determine the keys
keyP1602
- 基于51单片机的矩形键盘，用1602显示按键值-Based on 51 single rectangular keyboard, display the key value with 1602
Scan-button
- 利用C51编写4X4矩阵键盘扫描程序，在PROTUES中进行仿真，随着按键的不同，P2口的数据指示按键值。-Prepared using C51 4X4 matrix keyboard scanner, in PROTUES the simulation, with the key difference, P2, the data indicate key value.
IR
- 用2位数码管显示红外遥控发射器的按键值，显示用1602显示。-With two digital display Infrared remote control transmitter button values, display with 1602 display.
keypress-case
- 可以用此软件来识别iptv上面的按键值，以此来捕获按键响应-You can use this software to identify the key value above iptv