搜索资源列表
gongcheng
- 利用msp430149做的简单数控直流电源 可实现0—9.9v的电压输出 步进0.1 带键盘输入-Done using a simple numerical msp430149 DC power supply can achieve 0-9.9v output voltage step of 0.1 with keyboard input
main
- 全国大学生电子竞赛 单片机 数控直流电源凌阳61-National Undergraduate Electronic Contest Sunplus chip digital DC power supply 61
SHUKONGDIANYU-
- 数控直流电源源代码C语言编程 89c52单片机控制 -NC DC stream of C language programming code 89c52 single-chip control
dainyuan
- 基于msp430单片机的脉宽调制pwm控制的数控直流电源函数,经过149及169验证的-Msp430 microcontroller based pwm pulse width modulation control of digital DC power supply function, 149 and 169 after verification of
msp430_power
- 名称:简易数控直流电源 主控芯片为MSP430F149,步进0.1V,可在0到9.9V预置,可实现长按加减,步进同样为0.1V。-Name: simple numerical control dc power Main control chip for MSP430F149, step 0.1 V, can be in 0 to 9.9 V preset, which can realize long press to add and subtract, stepping the sam
123
- 利用avr16做的一个数控直流电源0~10电压可调 并读取电压值-Use avr16 do a numerical control dc power 0 ~ 10 voltage can be adjusted and reads the voltage
the-numerical-control-dc-power
- 本文主要论述了一种基于51单片机为核心控制器的数控直流电源的设计原理和实现方法。该电源具有电压可预置、可步进调整、输出的电压信号和电流信号可同时显示功能。文章介绍了系统的总体设计方案,其主要由微控制器模块、稳压控制模块、电压/电流采样模块、显示模块、键盘模块、电源模块五部分构成。-The method of this paper based on the 51 microcontroller core of the numerical controller DC power supply des
P
- proteus是数控直流电源仿真图含程序代码-efbreuthr4jtr4 545
shukong
- 该程序用51c语言编程,用于数控直流电源的数控,可以预置0~9.9之间的任意一个数-The program 51c language programming for the CNC CNC DC Power, can be preset to any number of between 0 to 9.9
shukongdianyuan
- 数控直流电源的程序,电子设计比赛时做的,调试过了-CNC DC Power program, electronic design competition, commissioning had
Numerical-control-dc-power-
- 数控直流电源,以STC89C52单片机为核心,由D/A数字模拟转换模块、功率放大模块、校验模块、键盘、LCD串口显示模块等模块组成一个数控直流电源-CNC DC Power, microcontroller to STC89C52 as the core of the D/A digital to analog conversion module, the power amplifier module, check module, keyboard, LCD serial port the di
dianyuan
- 简易数控直流电源的设计方案,包含设计电源,-Simple NC-DC power supply design, including design power
program
- 简易数控直流电源-Simple NC DC power supply. . . . . . . . . . . . . . . . . . . . . . .
chengxu
- 数控直流电源 jianpan saomiao lcd xianshi-shu kong zhi liu dian yuan
control-DC-power
- AT89S52单片机数控直流电源原理图程序资料-Single chip microcomputer control DC power diagram program data
DC_power
- 数控直流电源,C语言编程,可实现多种状态下的报警提示,没有仿真,也没有PCB,但程序调试成功。-NC DC power supply, C language programming, you can achieve a variety of state of the alarm, no simulation, no PCB, but the program debugging success.
STM32
- 数控直流电源,通过4*4按键输入所需电压,PWM调节BUCK电路的开关管的导通时间调节到你所需的电压-NC DC power supply via 4* 4 keypad enter the desired voltage, PWM BUCK regulator circuit switch conduction time adjusting to your desired voltage
shukongzhiliu
- 数控直流电源 单片机程序 用51单片机来控制直流 从而达到平衡
OK
- 基于MSP430F149的数控直流电源的详细设计,含原理图。-The detailed design of CNC DC power supply based on MSP430F149, including schematic diagram.
www
- :数控直流电源,本程序设定S9键为增加键,当按住S9键不松开时,输出Vout以0.1V连续步进, //直至键S9松开,当以一定的时间间隔点动S9键时,输出Vout也为点动步进 //递减键S11的功能与S9基本相同时,输出电压的值显示在LCD评上-LCD shuzi zhiliu dianyuan