搜索资源列表
shumaguan
- 用c语言编写单片机驱动数码管程序程序 简单-Using c language Microprocessor digital control program program simple
595
- 595比较器的典型使用方法:驱动LED数码管的函数(并行转串行)-The typical comparator 595 to use: drive LED digital tube function (parallel to serial)
d2009042316063174
- 本设计的指导思想是利用红外发光管发射红外线,红外接收管接收此红外线,并将其放大、整流形成高电平信号.当有人或物挡住红外光时,接收管没有接收到红外信号,放大器将输出低电平,同时将这个电平信号送入单片机进行控制计数,并经译码驱动电路使数码管显示数值。这样就得到要统计的人或物的数量。-The design of the guiding idea is to use infrared emission infrared LED and infrared receiver to receive the i
LED_7seg
- 这是28DSP的驱动数码管的程序,是光盘里带的-This is 28DSP drive digital control procedures, is the CD-ROM Li Dai
danpianjiyuanchengkongzhi
- 文章介绍了用AT89S8252单片机的串行接口与智能温度巡回检测仪(XJ-08S)通过RS—485总线相互通讯实现热水温度远程显示的一种低成本解决方案,内容涉及RS—485总线通讯、单片机驱动数码管显示、数据转换以及键盘处理软硬件设计等内容。-This paper introduces the serial interface using AT89S8252 microcontroller and Intelligent Temperature Loggers (XJ-08S) via RS-4
led8
- 微处理器实验时,用于八段数码管的点亮。含驱动程序。且可以输入要显示的数字。-Microprocessor experiment, for the Ba Duan digital tube light. With the driver. And can enter the number you want to display.
PCF8591AD
- PCF8591AD.C PCF8591的AD转换实验. /*芯片PCF8951共有四个A/D输入通道:AD0,AD1,AD2,AD3,分别与四个电位器(R1,R2,R3,R4)连接,用以调节电位器的输出电压。其中AD0通道既可测量电位器输出电压,也可用于测量从J1插座输入的外接电压,须用开关J2加以选择。J4插座提供由PCF8591输出的时钟方波信号。SAA1064驱动四个数码管显示一路AD转换后得到的数据-PCF8591AD.C PCF8591 of AD conversion exper
7218
- 7218驱动8位数码管显示,00-99循环显示,驱动程序-7218 Driver 8-bit digital display ,00-99 cycle showed that the driver
MicroPrinterDriver
- 该程序实现微型打印机的单片机驱动,并带有数码管显示功能-This program realization of single-chip microcomputer printer driver, and digital tube display function
shumaguan
- SPI接口实险,动态LED数据管显示实验。 1、程序通过SPI接口输出数据到HC595芯片驱动LED数据管简单显示。 2、动态调度由片内定时器1中断产生,中断周期为5mS。 3、内部1 M晶振,程序采用单任务方式,软件延时。 4、进行此实验请插上JP1的所有8个短路块,JP6(SPI_EN)短路块。 AVR mega16学习板 数码管显示函数文件-SPI interface to real risk, dynamic LED tube showed that t
Seg7
- 用SST89驱动四位七段数码管显示0-F的数据,包含写断码数据和写位选数据两部分。-Four seven-segment with SST89 drive digital display 0-F data, including data and write code to write off data Choice of two parts.
jtd3
- 简易交通灯程序,由hcf451驱动数码管-Simple traffic light program, driven by the digital control hcf451
74LS164
- 74ls164驱动数码管 -74ls16474ls16474ls16474ls164
qqyyclock
- 自己制作的电子时钟KeilC源程序,89C52驱动LED数码管,实现时间,日历,星期,温度,7组闹钟,每组闹钟可单独调节为不同的闹铃模式,四个按键控制-My design electronic clock, KeilC source, 89C52 drive LED digital, to achieve time, calendar, week, temperature, 7 groups of alarm clocks, each clock can be individually adju
timer
- 51单片机两个I/O口通过74HC164驱动六位数码管,时钟显示-51 MCU of two I/O port driver 6 through 74HC164 digital control, clock display
WDS18B20
- WDS18B20.C 数字温度传感器DS18b20测温实验:P0.0连接SDA, P0.1`连接SCL. SAA1064驱动四位数码管显示温度值:< 0 1 3. 4>-WDS18B20.C digital temperature sensor DS18b20 Temperature experiments: P0.0 connection SDA, P0.1 `connect SCL. SAA1064 drive four digital display temperature v
WDS1620
- *DS1620.C 数字温度传感器DS1620测温实验: P0.2接DQ位 P0.3接 CLK位,P0.4接RST位,P0.0接SDA,P0.1接SCL. SAA1064驱动四位数码管显示温度值:< 0 1 3. 4> -* DS1620.C digital temperature sensor DS1620 Temperature experiments: P0.2 then P0.3 access CLK DQ bit bit, P0.4 access RST b
SPI
- SPI驱动74HC595,数码管显示0~9999,帮助掌握单片机的SPI通信及定时器功能。-SPI communication
V1_3
- 1.5位数码管显示,静态驱动 * 2.定是功能(设定时||分||秒,到时间报警) * 3.锁定,清除,断电记忆功能 * 4.按键加一功能&&嗡鸣器响一声 * 5.接口可扩展如:感应,轻触开关 * 6.采用显示板&主板分开(如果能做成一块板也可以,元件可以放在显示板后面) * 7.外发制作PCB,耐用 * 8.键值分布:(从下往上) * K1--“-”,K2--“+”,K3--“清零/时间调整”,K4--“功能键” * 模
HT1621.c
- HT1621显示驱动程序,驱动6个数码管,供学习使用