搜索资源列表
moto
- 自动绕线装置,通过C51控制步进电机的程序,包含LCD模块、AT24C08、zlg7290等-Automatic winding device, stepper motor control through the C51 process, including the LCD module, AT24C08, zlg7290 etc.
m
- 单片机实验教程,单片机实验教程,步进电机控制实验程序-Stepper motor control experimental procedure
ftp628_printer
- 这是在LINUX2.6.28下的FTP-628的驱动.编入内核即可.应用程序一次送入两行点阵数据,384*2个点阵,因为步进电机一步需要两行数据.在硬件上,请自行处理MOTO信号,和STB信号.可能PIN要先对.本人运行过了.没有问题.-This is LINUX2.6.28 under the FTP-628 driver. Can be incorporated into the kernel. Once the application data into two rows of dot m
bujindianji
- 步进电机四轮驱动,proteus开发,keilC程序,用于仿真。-Stepper motor four-wheel drive (proteus)
motor
- 本程序实现的是对步进电机的控制,主控机是AVR单片机,外圈有四个按键,功能分别为:加速、减速、正反转选择、励磁方式选择-This procedure is implemented to control stepper motors, the host computer is the AVR microcontroller, the outer ring has four key functions are: acceleration, deceleration, Reversible choic
MOTOR
- 用于控制步进电机运行的C语言程序,很不错哟。-Used to control the stepper motor to run the C language program, very good yo.
Micros(3)
- 用单片机控制步进电机的程序,用汇编语言写的-With the stepping motor of the program, written in assembly language
51IRocde
- 基于51单片机的红外收发程序,配合步进电机转动确定方位(待续)。-51 MCU-based infrared transceiver procedures established with the stepper motor rotation direction (to be continued).
SteppermotorVHDL
- 步进电机定位控制系统VHDL程序与仿真2010.5.4-Stepper motor position control system and simulation of VHDL 2010.5.4 Procedure
bujindinaji
- 6221mada.asm.........遥控电机程序, 按遥控器0-9步进电机正转0-9步,按遥控器11-19步进电器分别反转 dianji.asm..........步进电机正转,反转各3圈 keyd.asm............步进电机控制程序p3.2正转,p3.3反转,p3.4停止 步进电机接p1.0p1.1p1.2p1.3-6221mada.asm ......... remote control motor program the remote control is tra
motor
- 51系列单片机驱动步进电机控制系统电路及程序-51 series stepper motor drive circuit and program control system
2410stepmotor
- 该程序是一个基于s3c2440的步进电机驱动程序,开发平台为linux-The program is a stepping motor based s3c2440 driver development platform for linux.
(C51)
- 步进电机加速-匀速-减速运行程序(C51)-Stepper motor acceleration- constant speed- slow down running programs (C51)
StepMotor
- 步进电机的程序,里面有几个程序吧~~当然要看你说对应的电机能否与这个型号相符合-Stepper motor program, which has several programs it ~ ~ of course depends on whether you say the motor corresponding consistent with this model
C51commonlyusedassemblysubroutine
- C51常用汇编子程序:ACM-12864汉字液晶显示驱动程序,定时与中断类,Ad转换类,排序类,频率计,串行通信,代码运算类,DES算法演示,C51_table,I2c总线,IIC,键盘与显示类,交通灯,步进电机,电机控制,-C51 compilation of subprograms used: ACM-12864 character LCD driver, timer and interrupt class, Ad Conversion class, sort type, frequency
motor
- 这是一个步进电机的程序,对单片机的百叶窗控制有所帮助,能够参考一下-This is a stepper motor program, shutter control on the MCU help, can refer to
dianji
- 四相五线步进电机控制的测试程序,C51编写,读者可稍加修给即可应用-Four-phase five-wire stepper motor control testing procedures, C51 write, readers can apply a little repair to the
programe
- 本程序,采用c编程对步进电机正反加速减速的控制。-This procedure, using c programming speed up the deceleration of the stepper motor control of both positive and negative.
MP28GA
- 基于单片机的MP28GA步进电机原理及程序-Stepper motor based on single chip MP28GA principle and procedure
303012
- 单片机步进电机仿真,用12864液晶显示.附有程序.-I don t know how to say!