搜索资源列表
read
- 单片机测温然后通过串口将数据传到labview上位机上通过波形图表进行显示温度曲线,进行显示与所给期望进行对比-Single chip temperature measurement and then through the serial port to the data to the LabVIEW PC through the waveform chart display temperature curve, to display and compare to the desired
Sensirion_SHT7x_LabView_8.6
- 基于LabVIEW的SHT7x湿度温度传感器上位机软件-Based on LabVIEW SHT7x humidity temperature sensor PC software
DS18B20
- 通过IAP15F2K61S2单片机采集温度(DS18B20),通过串口上传到上位机-By IAP15F2K61S2 SCM collecting temperature (DS18B20), uploaded to the PC via the serial port
termodetector--zigbee
- 基于zigbee无线网络的红外测温工程,与上位机连接,可实时传送温度-Zigbee wireless network based on infrared temperature measurement engineering, and PC connections, real-time transmission temperature
wendushishishuaxin
- Visual Basic 编的上位机软件,用于与单片机通信将单片机读取DS18B20的温度值实时刷新显示,简单好用,经本人调试过的,初学VB串口编程的人一定-Visual Basic series of PC software for communication with the single-chip will be read Singlechip DS18B20 refresh real-time temperature display, easy-to-use, as I have bee
MPU6050
- 本程序实现如下功能:开机后,先初始化MPU6050等外设,然后利用DMP库,初始化MPU6050及使能DMP,最后,在死循环里面不停读取:温度传感器、加速度传感器、陀螺仪、DMP姿态解算后的欧拉角等数据,通过串口上报给上位机(温度不上报),利用上位机软件(ANO_Tech匿名四轴上位机_V2.6.exe),可以实时显示MPU6050的传感器状态曲线,并显示3D姿态,可以通过KEY0按键开启/关闭数据上传功能。同时,在LCD模块上面显示温度和欧拉角等信息。DS0来指示程序正在运行。-This pr
fansile
- msp430采集tmp101温度并uart到pc-MSP430 acquisition of TMP101 temperature and UART to PC
GPRS-date-collection
- 使用STM32F107VCT6芯片驱动SIM900A GPRS驱动模块,操作GPRS模块时,可以直接在搭配的3.2寸触摸屏上看到提示,最终实现定时上传温度数据。上位机可用socket工具来查看收到的数据。已经测试过,可以直接使用。-Use STM32F107VCT6 chip driver SIM900A GPRS drive module, GPRS module operation, can be seen directly on the prompt with 3.2-inch touch
temperature
- 采用Visual Basic设计上位机界面,实现多路信号进行实时长时间监测;最终接入热电偶,实现对四路温度的监测任务。-Using Visual Basic design PC interface, multi-channel signals in real-time monitoring for a long time the final thermocouple access, to achieve four temperature monitoring tasks.
temperature
- 51单片机温度传感器DS18B20程序,数码管显示,每隔5秒,当温度超过10度时,送至PC机。-51 single-chip temperature sensor DS18B20 procedures, digital display, every 5 seconds, when the temperature exceeds 10 degrees, to the PC.
NRF
- NRF,实现发送接收,采集温度瓦斯浓度,串口传入上位机显示-NRF, realize transmitting and receiving, collecting temperature gas concentration, the incoming serial PC display
zigebee-wendujiance
- 协调器建立ZigBee无线网络,终端节点自动加入该网络中,然后终端节点周期性地采集温度数据并将其发送给协调器,协调器收到温度数据后, 通过串口将其输出到用户PC 机。-ZigBee coordinator to establish a wireless network, a terminal node is automatically added to the network, then the terminal node periodically collect temperature d
stc51_DS18B20
- 快速读取八路温度DS18B20,采用8个引脚,在数码管上顺序显示各路温度,并检测器件是否正常,然后将各路温度通过串口发给上位机-Quick read eight-way DS18B20 temperature, using 8 pins, order on the digital tube display various temperature, and detection device is normal, then each temperature via a serial port sen
wendu
- zigbee通过协议栈点对点通信,终端使用DS18B20测温,将温度数据发送给协调器,协调器串口发送至PC机。-zigbee protocol stack by using point to point communications, terminal DS18B20 temperature measurement, temperature data will be sent to the coordinator, the coordinator sent to the PC serial po
yingjiandianlu
- 温度采集,数据传输连接上位机硬件电路设计,-Temperature acquisition, data transfer connection PC hardware circuit design,
PCP18b20Pshumaguan
- 基于51单片机的上位机+18b20+数码管检测温度,数码管和上位机显示温度-51 microcontroller-based PC+18b20+ digital temperature detection, digital temperature display and PC
com
- 电脑串口接收DS18B20温度测试程序 1、程序说明: 该例程演示了单片机采集温度,并将温度值 发送到电脑的测试程序, 2、实验操作 1、将跳线插座J11的跳线帽调至TDQ端。 2、将跳线插座J28的跳线帽跳到TxD1和RxD1。 打开STC-ISP下载软件中的串口助手,选择相应串口号, 选择波特率9600,8位数据位,1位停止位,无校验。 点打开串口 接收缓冲区选择“文本模式” 发送缓冲区选择“文本模式”
program_v1
- 温度数据采集系统上位机程序-Temperature data acquisition system PC program
temperature
- 51单片机进行温度测量,VB上位机进行数据采集控制继电器,程序编译可用。-51 single-chip temperature measurement, VB PC for data acquisition and control relays, compiled available.
CSharptemperature
- C#上位机编写的温度采集程序,并且可以实时进行绘图。编译可用-C# prepared by the PC temperature acquisition program, and can be plotted in real time. Compile available