搜索资源列表
1
- Duck公司在仓库安装了红外报警装置,如图所示,所有红外线互不相交。n个发射器和n个接收器将平面分成n+1个区域,从左到右分别记作0、1、…、n。现在技术人员正在进行调试,对于每个点,需要快速知道它处于哪个区域。若正好处于红外线上,则视为处于右边的区域。-Duck in the warehouse infrared alarm system installed, as shown, all infrared disjoint. n transmitters and receivers n n+
STM8S_TIM1
- stm8s基于库的红外线接收信号,已经编程好-The infrared receiver
ATMEGA16--hongwai
- AVR单片机ATMEGA16 C语言程序 红外线发射接收程序-atmega16 hongwai
set2-1
- Duck公司在仓库安装了红外报警装置,如图所示,所有红外线互不相交。n个发射器和n个接收器将平面分成n+1个区域,从左到右分别记作0、1、…、n。现在技术人员正在进行调试,对于每个点,需要快速知道它处于哪个区域。若正好处于红外线上,则视为处于右边的区域。-Duck in the warehouse infrared alarm system installed, as shown, all infrared disjoint. n transmitters and receivers n n+1
keil
- 基于51单片机的c语言实现的代码 包含 时钟 万年历 串口试验 温度显示 1602显示红外线值 EEPROM实验 AD和DA -Code 51 based SCM c language contains the serial clock calendar 1602 show infrared temperature display test values EEPROM experiment AD and DA
Arduino-xiaoche-daima(7)
- 智能小车开发程序之红外线遥控小车,通过将程序下载至arduino面板,智能小车根据红外探测仪智能避障。-Infrared remote control smart car development program of the car, through the program downloaded to arduino panel, smart car based on infra-red detector intelligent obstacle avoidance.
PWMCONTROLSETPMOTRA
- 开发平台:KEIL 设备:STC15F2K60S2 功能:红外线控制PWM波的输出,控制步进电机的转速,和循环次数.可以通过串口命令控制初始化参数-Development platform: KEIL Equipment: STC15F2K60S2 Function: infrared control PWM wave output, control the speed of the stepper motor, and the number of cycles.
HONGWAIXIAN
- 测量红外线遥控发出数据,在显示屏上显示哪个红外线发出的数值,-Infrared remote control data sent to the display, which shows the value of the infrared emitted,
pwm38K
- STC15w408 pwm产生38KH红外线信号c51程序-STC15w408 pwm generate 38KH infrared signal c51 program
cedingxinlv
- 这是一款通过手机摄像头测定心率的app,通过红外线测定,科学可用-This is a mobile phone camera by measuring heart rate app, by infrared measurement, available scientific
hongwaixian
- 编写的接收红外线的51单片机代码,有详细的注释和说明,容易读懂。-51 microcontroller code for receiving infrared
FXY
- 最近几天突然对红外线遥控器发生兴趣,于是上网混了一下,发现编码方式有好几种,而且同一种编码方式又有许多不同的细节,为了弄清楚手头的遥控器是出身何门,无奈手头又没有logic分析器之类可望不可及(广东话里“及”同“望”都系“睇”既意思)的东西,遂萌生了写这个软件的冲动。-Infrared logic analyzer
5-example_IR_1
- Espier_III开发板红外线通讯测试的实例程序-Espier_III development board example source code
int-main
- 本闹钟系统共有五个按键,各有不同的功能,每个按键按下都会发出提示音。前三个按键组合使用用于调节时钟第一次响铃和第二次闹铃的时间。第四个按键控制显示十五种心形流水灯效果,第五个按键按下时单片机先检测温度,然后控制语音芯片播报当前室温。当系统达到闹铃所设的时间时会有闹铃声音,只有通过手枪(经过玩具手枪改造可以发出指定编码的红外线)射出红外线才能停止,而且手枪瞄准位置误差太大时,闹铃将接收不到继续响铃,所以人必须稍微清醒并且瞄准目标才能关闭闹铃。当平时没有闹铃时若用手枪打闹钟,闹钟就会播放当前温度。另
hongwaiyaokong
- 这是基于52单片机的红外遥控的基本代码,单片机通过接收红外线码,然后再解码,读出红外信号。-This is based on 52 single-chip infrared remote control of the basic code, the microcontroller through the infrared code to receive, and then decode, read out the infrared signal.
hongwaidianji
- 这是一个基于红外线的控制的电机程序,你可以根据这个更改成你需要的程序-This is an infrared-based motor control program, you can change this as you need to program
hongwaijiance
- 基于51的红外线检测完整代码,经检测能完整运行。-Based on infrared detection complete code 51, the detection can complete run
hongwaiduishechuanganqi
- 红外对射传感器使用的是槽型红外光电开关。红外光电传感器是捕捉红外线这种不可见光,采用专用的红外发射管和接收管,转换为可以观测的电信号。红外光电传感器有效地防止周围可见光的干扰,进行无接触探测,不损伤被测物体。红外光电传感器在一般情况下,有三部分构成,它们分为:发送器、接收器和检测电路。-Infrared correlation of sensor using the infrared electric switch is groove. Infrared electric sensor is c
hongwaijiema
- 红外线解码程序,用于51单片机控制的红外遥控解码-Infrared decoding procedures for the 51 single chip microcomputer control infrared remote control
PIR_test2
- 人体红外线感应,走廊灯程序,有RGB7彩渐变-Human infrared sensor, hallway lights procedures, RGB7 color gradients