搜索资源列表
LPC2100_ADC
- 用于Philips ARM LPC2100 的模数转换器的程序,有汇编哦,当然也有C啊。对比着看很好啊!-for Philips LPC2100 ARM ADC procedures, a compilation Oh, of course, also has C ah. Compared to see good ah!
ADTEST
- 51单片机对模数转换器adc574/1674/ads774数据采集程序,采集数据BCD码在78~7B-51 microcontroller on the ADC adc574/1674/ads774 data collection procedures, BCD data collected in 78-7B
applicationofADC0804
- 单片机的数模转换程序 验证过 超好使 对于从事单片机数模转换是一个很好的例子 对于模数转换芯片资料可以到网上下载-MCU ADC-tested procedures for engaging in so few MCU mode conversion is a good example right in analog-digital converter chip information can be downloaded to the Internet
51asn
- 设计的温度采集模块是应用一个滑动变阻器通过改变电阻值进行模拟的温度值改变情况;模数转换模块是运用ADC0809芯片进行模数的转换,把采集到的模拟电压值变为数字值;单片机控制系统通过程序判断此数字值的大小,这样控制温度报警模块,一方面控制发光二极管的亮灭情况,另一方面控制蜂鸣器的报警;温度显示模块应用四位数码管显示模拟的温度值。因此,构成了此模拟的温度控制系统。本系统主要实现了模拟的温度值在30到60的一个设定范围内,正常显示温度,一旦超过了此范围,就会有报警。-design of the tem
fpgacaiji
- 自己课程设计写的程序,用FPGA控制ADC0809的转换时序来完成模/数转换,然后将转换完的数字信号传递给0832-write their own curriculum design process, Connection between ADC 0809 FPGA control the timing to complete the conversion analog / digital conversion, End then converting the digital signal to
ADC
- 数模转换程序,应用对模数的转换功能,此程序就是完成这种更能。
7841
- 模数转换器ADS7841的驱动程序,经过自己验证可用-ADC ADS7841 driver be used after their validation
adc0809
- 基于 80C52 单片机的 adc0809 模数转换 c程序,使用了IN0口,-Based on 80C52 microcontroller adc0809 ADC c procedures used IN0 mouth
0809_diver
- 该程序可以驱动ADC0809,实现模数转换-The program can drive ADC0809, ADC implementation
my_AD2543_driver
- 该程序可驱动TLC2543,实现模数转换-The program can drive TLC2543, ADC implementation
msp430
- msp43022*4单片机模块的测试程序,包括IO口、clock、flash、模数转换、WDT等。-msp43022* 4 single-chip module test procedures, including the IO port, clock, flash, ADC, WDT, etc..
DAC
- 本程序使用C8051F020单片机自带的模数转换器,进行模数转,输出模拟电压。-C8051F020 single chip uses the built-in ADC, the analog-to-digital switch, the output analog voltage.
shiyan10
- A/D、D/A转换程序设计 加深理解逐次逼近法模数转换器的特征和工作原理,掌握ADC0809的接口方法以及A/D输入程序的设计和调试方法。-A/D, D/A conversion process designed to deepen understanding of the successive approximation ADC characteristics and working principle of the interface methods have ADC0809 and A/D
adc7886
- 模数转换器ADC7886的驱动源程序,包含去极值求平均和得到当前单个转换结果的程序-ADC7886 ADC driver source code, including the average to extreme demand and receive the results of the current procedures for a single conversion
adc
- AD数模转换程序,是设计数据采集的一个参考c语言代码-AD digital-analog conversion process, is designed as a reference data collection c language code
adc
- mega 8 模数转换模块演示程序代码, 用来进行模拟输入转数据输出-mega 8 analog to digital conversion module demo code
ADC
- C5051F330单片机模数转换范例程序,非常实用,开发板实用版。-C5051F330 single-chip analog-to-digital conversion example program, very practical, development board practical version.
adc.tar
- mini2440开发平台基于linux3.0的模数转换驱动程序,包括测试程序在内-develop board mini2440 ADC driver on linux3.0 kernel
实验17 ADC实验
- 首先介绍了STM32 ADC的功能,通过对各寄存器的分析,编写了模数转换的程序。(Firstly introduces the function of the STM32 ADC, through the analysis of the register, write the analog-to-digital conversion applications.)
Example22_DSP2833x_ADC_soc
- 当需要采集外部信号时, 外部信号多数是模拟信号, 如电压、 电流、 压力、温度、 湿度、 速度等, 而单片机又只能处理数字信号, 因此就需要一个将模拟信号转换为数字信号的介质--模数转换器(ADC) , F28335 芯片内部含有 ADC 外设,本程序实现了 F28335 的 ADC 模数转换功能。