搜索资源列表
OFDM_Performance_Vs_CFO
- Carrier frequency offset in ofdm communication system in Matlab. it shows BER vs SNR.
OLA_OOPSim
- Opportunistic Large Array 的MATLAB 模拟器. Object oriented Event Based 无线广播 支持OLA 累积Relay重发信号以达到最佳解码效果 节点位置可随机或以网格生成 可控制调变方式 独立节点间无线传输信道模型 可调随机生成信噪比范围 生成显示各节点位置图 生成各节点接收所需OLA副本数量图 生成各节点误码率图 生成各节点HOP-COUNT图
Diversity_BER
- BER performance of RGC and MRC in matlab
frequency-offset-in-ofdm
- This Matlab scr ipt finds the frequency offset effects in the orthogonal frequency division multiplexing (OFDM)and its effects on the bit error rate (BER). A reference paper is also included.-This Matlab scr ipt finds the frequency offset effect
2013102244433157
- OFDM在瑞利信道下的误码率，使用matlab将OFDM在瑞利信道下进行仿真性能的效果-OFDM BER in Rayleigh channel using matlab OFDM in the Rayleigh channel simulation performance results
BER-simulation-for-BPSK-with-AWGN
- With this matlab codes one can simulate BER for BPSK Modulation with added noise in various steps
DS-CDMA
- DS-CDMA signal transmission simulation in MATLAB. Inludes: FEC, RF_sig+Rician channel, Equalizing, BER calculation.
BPSK-and-QPSK-BER-simulation
- 用matlab编写了BPSK 和QPSK 两种调制在高斯白噪声信道和瑞利信道下的误码率仿真曲线，并做了对比。-the texts simulate two modulaton BPSK and QPSK in both AWGN channel and Rayleigh channel, also did the comparison between two mudulation.
code-matlab
- 利用SIMULINK和M函数相结合的方式仿真BFSK 调制在多路径瑞丽衰落信道中的传输性能。其中 source产生速率为10Kbit/s、帧长度为1秒的二进制数据源data,并且通过BFSK产生调制信号。BFSK调制的频率间隔为24KHz, BPSK调制符号的样点数为2，调制信号通过多径瑞利衰落信道，移动终端相对运动速率为40公里/小时，接收端对信号进行解调，并把解调后的信号和原始数据信号相比较计算误比特率。最后Sink模块根据SNR与误比特率的关系绘制曲线。-And M functions u
BER_of_BPSK
- BER of BPSK modulation in Matlab is presented
cn_qpsk
- 在matlab中仿真QPSK各项性能。包括星座图，调制波形以及在AWGN和Rayleigh信道中的误符号率与理论值的对比。解压后粘贴主程序和子程序到3个m文件即可运行。-Simulate the QPSK based on matlab. Specifically include the constellation diagram, and BER in AWGN and Rayleigh channel.
16QAM
- 在matlab中仿真16QAM的系列特性，具体包括星座图，信道w误符号率等-simulate the 16QAM in matlab. Specifically include the constellation diagram and the BER
QPSK-BER
- 一个仿真数字带通QPSK调制系统的误码率的matlab程序。无论是仿真带通系统还是基带通信系统，通信系统模型的误码率的计算过程主要由设置相关参数、创建信号、即信源编码、调制、对调制信号添加高斯噪声、解调、计算系统的误码率等步骤组成。这个例子详细介绍如何利用matlab通信工具箱中提供的函数实现系统的误码率的仿真。-BER simulation of a digital bandpass QPSK modulation system matlab program. The simulation s
Ber-for-Bpsk-in-OFDM
- 用MATLAB实现OFDM系统中 ，在瑞利多径衰落信道下，用BPSK调制的误比特率曲线。-BER for BPSK in OFDM with Rayleigh multipath channel
Mote_Carlo_snr_ber
- 蒙特卡洛法对2psk,2fsk通信系统进行仿真，计算不同信噪比(SNR)条件下的误码率（BER）并画图-2PSK,2FSK communication system simulation using Monte Carlo method in MATLAB, calculating the different BERs for different SNRs and plot figures.
rs
- RS码的C实现，通过mex接口，在MATLAB中创建的LTE下行链路中测试，可跑出误码率曲线。-RS code is implemented in C, by mex interface, LTE downlink created in MATLAB test can be run out of BER curves.
Diversity_BER
- BER performance of RGC and MRC in matlab
GF4_FFT
- 用Matlab仿真四元LDPC码并得出误码率曲线图。-Simulation quad LDPC codes in Matlab and draw BER curve.
berj
- To calculate the Bit Error Rate (BER)of AWGN channel for a given range of SNR in MATLAB
bit-error-rate-matlab
- 详细说明了应用matlab对数字通信领域一重要指标BER仿真的过程与方法。-Matlab is an ideal tool for simulating digital communications systems, thanks to its easy scr ipting language and excellent data visualization capabilities. One of the most frequent simulation tasks in the fi