搜索资源列表
PIC蜡烛灯模拟程序
- 利用PIC12F675控制LED的闪烁，模拟蜡烛灯的摇曳状态。压缩文件里面包含有PIC源文件,HEX文件，还有仿真文件。
LED灯闪烁
- LED跑马灯测试时钟
test LED
- Spartan 3E 开发板上LED灯循环闪烁-Spartan 3E development board flashing LED lights cycle
led
- 用一个按钮开关循环控制四个led灯的闪烁方式，输入时钟10MHz，闪烁频率1Hz-Button switch with a four cycle control lights flashing led the way, the input clock 10MHz, blinking frequency of 1Hz
LED
- 详细说明：这是一个TI DSP2812的GPIO的应用: 跑马灯程序,可以让8个Led灯,每隔一秒钟依序轮流闪烁,附录了完整的程序批注-Detailed Descr iption: This is a GPIO of TI DSP2812 Application: Marquee procedure allows 8 Led lights, then take turns at intervals of one second flashes, appendix a complete endors
top
- 实现定时器功能，分别有秒针，分钟，小时，到一天后led灯闪烁一下。-To achieve timer function, respectively, seconds, minutes, hours, to one day look after the led light flashes.
led
- 基于davinciDM6446的led灯闪烁实验，是在dsp端的。-It is a led program based on davinci DM6446 , it is about dsp.
gpio_flash
- DSP F2812 LED灯闪烁实验FLASH烧写程序-DSP F2812 LED lights flashing experimental procedures FLASH programmer
1.LED
- 用于CC2430芯片ZIGBEE调试用的。简单的LED灯闪烁程序-Use for ZIGBEE CC2430 chip debugging ,Simple LED flashing program
led
- 基于TMS320VC5416的定时器编程，DSP工作在8MHZ主频，定时器分频系数为15，通过DSP通用I/O引脚控制指示灯闪烁，指示灯每秒闪烁1次。-TMS320VC5416 timer based programming, DSP working in 8MHZ frequency, the timer frequency factor of 15, through the general-purpose DSP I/O pin control light is blinking, the
LED-lights-flashing-CC2430
- 基于CC2430开发板的一个实验例程 开发环境为IAR Embedded Workbench 实现功能为：LED灯闪烁-CC2430 development board based on an experimental routine IAR Embedded Workbench development environment for the realization of functions: LED lights flashing
Key-control-led-cc2430
- 物联网必学 CC2430开发板得一个实验例程 实现功能为按键控制LED灯闪烁 开发环境应为 IAR Embedded Workbench-Things will have to learn CC2430 development board features an experimental routine to achieve control of LED lights flashing for the key development environment should be IAR Embed
ucos-under-the-LED-flashes
- ucos under the LED flashes关于LED灯闪烁的一个简单的小例子，是在移植的基础上实现的-ucos under the LED flashes
Led
- 单片机 控制led灯 闪烁 led流水灯-SCM led lights flashing led light water
LED
- 第一个LED灯闪烁 LY5A-L2A开发板-The first LED flashes LY5A-L2A development board
单片机汇编：LED灯控制实验
- 1 .LED闪烁 2 .二进制加法 3 .LED流水灯 4. 跑马灯 5. 左右跑马灯(The assembly program of the LED lamp control experiment)
雾灯程序
- 基于AT80C51单片机的控制雾灯闪烁频率，亮度等级(Control fog light flicker frequency, brightness grade based on AT80C51 single chip)
ZIGBEE仿真器USB驱动(不需要安装放桌面就可)
- 控制LED灯闪烁，每秒闪烁一次 ，当按键按下，LED1闪烁，按键再次按下 LED1熄灭(control LED good good studt)
com口控制led灯
- com口发送指令来控制led的闪烁情况（库开发）(com mouth led lights control)
LED (2)
- 初始化GPIO，使LED灯闪烁 、、、、、、、、、、、、、、、、、(Initialize the GPIO and make the LED light flicker)