搜索资源列表
CC2430-3
- CC2430基础实验三,按键控制闪烁,这是通过按键控制LED灯的闪烁。-CC2430-based experimental three buttons control the flash, which is controlled through the buttons flashing LED lights.
16c54
- 3个按键底电位有效来控制4个LED灯的闪烁方式-3 buttons at the end of the effective potential to control the 4 LED lights flash mode
T0_ASM
- 51单片机定时器点亮LED灯,使其闪烁,定时时间可修改-51 MCU timer light LED lamp, it flashes, time period may be modified
fsd
- 本系统采用MSC-51系列单片机ATSC51和可编程并行I/O接口芯片8255A为中心器件来设计交通灯控制器,实现了能根据实际车流量通过8051芯片的P1口设置红、绿灯燃亮时间的功能;红绿灯循环点亮,倒计时剩5秒时黄灯闪烁警示(交通灯信号通过PA口输出,显示时间直接通过8255的PC口输出至双位数码管);车辆闯红灯报警;绿灯时间可检测车流量并可通过双位数码管显示。本系统实用性强、操作简单、扩展功能强。 -The system uses MSC-51 Series Microcontroll
DE2_LED_ON
- 一个简单的led闪烁程序,检测DE2学习板的led灯,用verilog语言编写-A simple blinking led program to petect learning DE2 board led lights, with the verilog language
Blink
- 基于nesC的无线传感器网络节点led灯的闪烁-NesC-based wireless sensor network node led flashing light
Lighting
- 基于无线传感器网络节点的led灯流水闪烁!-Wireless sensor network node led lights flashing water!
lab9
- 交通灯用于交通灯LED灯轮流闪烁并可以根据要求闪烁-Traffic lights for traffic lights and LED lights flashing alternately flashing according to requirements
8255keyboard
- A)利用8255作为简单输入输出接口,设计开关控制电路,实现对3位7段数码管进行控制,开关闭合,7段数码管显示自动加一,到999重新显示000;开关打开,数码管显示暂停。 B)利用8255作为简单输入输出接口,设计2×2按钮阵列电路,实现对3个led(红黄绿)控制,要求对按钮编号,实现按钮A按1次红灯闪烁10秒、按钮B按1次绿灯闪烁15秒、按钮C按1次黄灯闪烁10秒、按钮D按1次全部常亮。 -keyboard
DP512ATD
- MC9s12dp512的一个ATD例程,读取和显示LED灯的电压,使多个LED按一定规律闪烁。-ATD MC9s12dp512 a routine to read and display the voltage LED lights to make multiple LED flashes according to certain laws.
include
- 通过实验箱上的通用控制模块的键盘选择,通过定时器的计数和延迟来控制LED灯的不同图案的闪烁.-Experimental box by a common control module on the keyboard options and delayed by the timer counts to control the LED lights flash in different patterns.
GPIO
- 简单的嵌入式系统设计实验,实现GPIO实验,使4个LED灯交替闪烁。希望对各位有用。-Embedded system design simple experiments to achieve GPIO experiment, so that 4 LED lights flash alternately. You want to be useful.
demoXEPSCI
- 飞思卡尔单片机串口通信程序设计,实现功能:①将从串行口收到的数据原样发送到串行口。 ②根据从串行口收到的数据控制四种不同的LED显示效果, 收到字符’1’:LED灯的效果为实验一中的效果1,并向串行口发送字符串“LED效果1”; 收到字符’2’:LED灯的效果为实验一中的效果2,并向串行口发送字符串“LED效果2”; 收到字符’3’:LED灯的效果为实验一中的效果3,并向串行口发送字符串“LED效果3”; 收到字符’4’:LED灯的效果为实验一中的效果4,并向串行口发送字符串
led_test
- 在FPGA上实现LED流水灯闪烁的测试程序代码-Water in the FPGA to achieve LED lights flicker test code
timedled
- 小灯闪烁,自己在Spartan-3e板上测试用的-blink LED
led1
- led闪烁灯,本代码仅供交流学习,未经同意不得用于其它商业用途。-xiao deng pao
liushuideng
- 这个程序是基于AT89S52单片机的实现LED灯轮流闪烁的程序。-This procedure is based on the realization of AT89S52 MCU flashing LED lights program.
led
- 利用动态扫描和定时器1在数码管上显示 出从765432开始以1/10秒的速度往下递减 直至765398并保持显示此数,与此同时利 用定时器0以500MS速度进行流水灯从上至 下移动,当数码管上数减到停止时,实验 板上流水灯也停止然后全部开始闪烁,3秒 后(用T0定时)流水灯全部关闭、数码管上 显示出"HELLO",并保持-Dynamic scan and Timer 1 in the digital pipe shows start from 765 432 to 1
GPIOLed01
- 使用PWM1-PWM6引脚作为通用的I/O口来控制Basic2812上LED灯 D1-D6的闪烁-Use PWM1- PWM6 foot as gm s I/O port Basic2812 to control the LED lights flashing D6- D1
paomadeng
- 一个单片机开发的示例程序,可用开发板实现LED灯的循环闪烁-A Single Chip sample program can be used to achieve development board cycling flashing LED lights