搜索资源列表
Nixietube
- MSP430控制数码管闪烁，采用扫描方式，以验证。我已上传6个源码，大约含15个源码，麻烦站长帮我开通，谢谢您！-MSP430 control LED flashes, the use of scanning to verify. I have uploaded six source, containing approximately 15 source, the trouble to help me open head, thank you!
Shuma
- 基于MSP430F149单片机的数码管周期性变换闪烁程序-MSP430F149 single-chip based on the cyclical transformation of the flashing LED program
AD_count_countdown
- 设置3个功能键：当某一功能键被按下后，进入相应的功能模式。3个功能有： 1）8路数据采集功能：通过调节可变电阻实现0-5V的电压输出作为8路输入信号使用，每路信号用2位LED显示采集的结果。报警：任意一路超过某一门限（可自己设定）时，发出报警（声音+灯闪烁，并通过灯指示是哪一路报警），同时停止采集。2）计数功能：利用计数功能键，实现每按一次按键，LED显示加1，从0-99计数。3）秒表功能：只用一个键控制。按下一个按键后时钟启动，从零开始计时，计时间隔0.01秒，再按一次后停止。再按一次后清
blinky
- 利用keil和C8051F120制LED的闪烁-via software keil and C8051F120 yield LED blink
flowlight
- 8个发光管间隔200ms由上至下，再由下至上，再重复一次，然后全部熄灭再以300ms间隔全部闪烁5次。重复此过程。-8 LED 200ms interval from top to bottom, then bottom, then repeat, and then all go out again to 300ms interval all flashing 5 times. Repeat the process.
CC2430-3
- CC2430 基础实验三按键控制闪烁 本实验的控制比实验二的控制稍显复杂，这个实验中使用按键控制LED 或闪烁，或熄灭。-CC2430 experimental basis for the three flashing button control of the control in this experiment than in the control of the second experiment a little complex, this experiment to control
read
- 以51系列单片机(AT89C51)为核心，配以相应硬件电路，实现密码的设置、存贮、识别和显示，完成密码锁的模拟。单片机接收键入的代码，并与存贮在数组code_ram[6]中的密码进行比较，如果密码正确将会显示OPEN，如果密码不正确，将显示NO，并且允许操作人员重新输入密码，最多可输入三次；如果三次都不正确，则单片将上锁，并显示LOCK。每次按键完成后，6个数码管将会闪烁显示“—”，表示单片机已经接收到了输入的数据。-51 Series single-chip microcomputer (AT
TINDlay
- 定时器延时程序,LPC2132定时器0分频之后开匹配0中断。实现LED的闪烁（先说时间可以改）-Tin Delay
P1kongzhidengshangsuo
- P1口作输出口，接八只发光二极管，编写程序，使发光二极管闪烁点亮。-1.P1 port for output, and then light-emitting diodes 8, the preparation procedure, so that LED light flashes.
FlashLED
- 基于DY-mini80单片机学习板_闪烁小灯设计。三个按键控制8位LED小灯三种显示花样。-DY-mini80-based single-chip learning board design _ flashing lights. Three buttons to control 8 LED lights show the pattern of three.
C8051
- C8051F系列单片机串口通讯程序，串口编程--接收PC发来的字符串,回发字符串.发送期间中断控制LED灯闪烁-C8051F series single-chip serial communication program, serial programming- PC sent to receive the string, back-fat string. Sent during the interruption of control blinking LED lights
c51
- LED流水灯 * * 功能：操纵板上8个LED发光管闪烁 这个不是我自己做的，是例子程序-LED water lamp** function: 8 LED control board LED flashes to do this instead of my own is an example program
pjt
- avr单片机的扫描按键程序编写和二极管闪烁-avr microcontroller programming scan button and the LED flashes
nn
- P1端口接八只LED，每次点亮一个，先左移2次，再右移2次，然后闪烁2次，重复循环。-P1 8-port access LED, lighting each one, first the left 2 times, and then shifted to right 2 times, and then flashes 2 times, repeat the cycle.
2812_bios_modul_flash
- TMS320F2812 的基于bios的烧入flash运行的工程，运行结果是一个io口控制的led灯不停闪烁。bios烧写需要经过较多的配置过程，可以此作为基础添加自己的代码，就可以将工程烧入flash运行，免去重新配置的麻烦。-TMS320F2812-based burn into the flash of the bios to run the project, run result is a mouth-controlled io non-stop flashing led lights.
light_text
- 基于c8051f340的引脚测试程序，若引脚未损坏，则接上led灯后，灯会一闪一闪的，否则灯不会闪烁-On c8051f340 pin test procedures, if the pin is not damaged, then connect led lamp, the lantern flicker, or light does not blink
lesson02code
- 发光二极管闪烁时间可控的程序，适合初学者使用。-LED blinking time controlled process, suitable for beginners.
MSP430LED
- 基于MSP430F149单片机的LED各种闪烁程序，适合初学者学习。-MSP430F149 microcontroller-based LED flashes a variety of procedures, suitable for beginners to learn.
breakINT0
- 演示89C52响应中断：没有中断时，4个LED灯以闪烁为主，响应中断后则以广告灯的形式显示。由于采用下降沿触发，所以对于中断有一次记忆功能。-Demo 89C52 to respond to interrupts: No interrupt when the four LED lights to flash the main, the response disruption Zeyi advertising in the form of light display. As a result of
aicheyizu
- C51单片机控制LED灯闪烁（用于汽车警示作用）。-C51 SCM control LED lights flashing (for automotive warning).