搜索资源列表
c5
- 以上是单片机控制的典型应用 包括了中断 时钟 继电器输出 串口通讯 这要在单片机上才能运行起来-The above is a typical MCU control applications include a serial communication interrupt clock relay outputs which should be up and running on a microcomputer
c1
- 我上传的5个文件都是在单片机下运行的 主要是中断 通讯 继电器驱动 时钟 等 -I uploaded 5 files are running under the SCM was mainly driven clock interrupt communications relay
c2
- 我上传的5个文件都是在单片机下运行的 主要是中断 通讯 继电器驱动 时钟 等-I uploaded 5 files are running under the SCM was mainly driven clock interrupt communications relay
c3
- 我上传的5个文件都是在单片机下运行的 主要是中断 通讯 继电器驱动 时钟 等-I uploaded 5 files are running under the SCM was mainly driven clock interrupt communications relay
c4
- 我上传的5个文件都是在单片机下运行的 主要是中断 通讯 继电器驱动 时钟 等-I uploaded 5 files are running under the SCM was mainly driven clock interrupt communications relay
DN_BGMS
- 程序使用ISDN信令进行接续处理，IsdnSwitch.exe拨入彩话系统后，ColorTalk.exe接收呼叫，提示用户选择背景音乐歌曲编号，用户输入完成后，ColorTalk.exe选择一个空闲中继呼出，被叫号码全部转发到模拟交换机端。IsdnSwitch.exe接收呼叫，并根据被叫号码的后两位对坐席进行振铃(如后两位为00则对坐席通道0进行振铃，为01则对坐席通道1进行振铃，依次类推)，坐席摘机后ColorTalk.exe建立会议，开始放音，这时可进行通话并伴有背景音乐。-Procedur
timer
- Atmega8 Timer with seven segment display and relay action
qrs
- 通过串行口，提示用户输入倒计时时间(0~999秒)； 时间设定完成后提示用户选择控制方式：“倒计时开”还是“倒计时关”； 若用户选择 “倒计时关”，继电器立即吸合，并倒计时直到时间为0时关断继电器； 若用户选择“倒计时开”，继电器暂不吸合，等倒计时时间为0时再吸合继电器； 倒计时时间通过串口送上位机(每秒更新一次)； 倒计时结束时蜂鸣器鸣响2秒作为提示； -Through the serial port, prompts the user to enter th
VALVEC
- PIC16873无线模块控制继电器，可根据收到的命令闭合或断开继电器完成简单的控制功能-PIC16873 wireless module control relays can be closed based on the receipt of orders or disconnect relay to complete a simple control functions
MicrocontrollerBasedElectronicCodeLockDesign
- 设计以电磁继电器模拟密码锁，由单片机8051来控制锁的打开与闭合，由HD7279来管理器键盘及显示，密码从键盘输入，用8051来控制7279显示当前锁的状态信息及报警。本次设计用单片机开发系统来模拟密码锁的多种功能，密码由4-6位数字组成，当输入密码相符时开锁，输入三次不符报警，同时密码输入正确时可以修改密码，此时指示灯亮。开锁单片机开发出开关量，通过光电耦合器控制，打开密码锁。报警则由单片机发出报警信号，控制音频放大电路发出报警声音。-Designed to simulate electrom
Untitled
- BER of Orthogonal STBC over Rayleigh fading
Uart_V3
- 开发环境 KEiL C 单片机 华邦W77E58 功能 串口收到“0”使P1口的灯流水闪烁，收到“1”停止，还有继电器有动作。另外加了W77E58特有的看门狗程序。-Winbond MCU development environment KEiL C function serial W77E58 receive a " 0" so that P1 mouth water flashing lights, receive a " 1" to stop,
djs
- 按SW19独立按键，倒计时开始 倒计时期间 继电器吸合 按SW20键继电器断开 计时暂停 按板上单片机复位按键 计数值恢复为999 此计数初值 可在程序中修改。-Press SW19 independent button during the countdown to begin the countdown relay pull-off time by SW20 key relay suspended by the board microcontroller counts reset butto
Control_4
- 315遥控，控制4路继电器开关,系统最多可控制16路继电器-315 remote control, control 4-way relay switch, the system can control up to 16 relays
jidianqi
- 名称：继电器程序 功能：控制两个继电器轮流闭合，断开 分别由两个继电器控制的LED闪烁 -Name: Relay program features: control two relays alternately closed, disconnect the relay controlled by two LED flashes
GSM_RELAY
- circuit activate a relay when mobile phone rings with piezzo-circuit activate a relay when mobile phone rings with piezzo
dingshichazuo
- DS12C887时钟芯片，DS18B20温度传感，通过控制继电器成定时插座。有完整的代码。-DS12C887 clock chip, DS18B20 the temperature sensor, by controlling the relay into a regular outlet. A complete code.
radiocover
- 这个程序可以计算给定点处的小区信号范围覆盖。-is program computes a map of visibility from a selected point on a topography. It has been written to help the search for radio relay best location. Because it considers only direct line of sight, it gives a good estimation for
TC35-code
- TC35控制继电器源代码 供大家参考使用-TC35 Control Relay source code for your reference
4Rel_MSC-10
- domotic avr in order to control a relay card with can interface