搜索资源列表
TIME-SYNC-2051
- 工厂时间同步的单片机的源程序,驱动6个数码管-factory SCM time synchronization of the source, drive six digital control
LCD_DR
- //使用说明: //使用前请先定义keyscan为单片机的 //某个端口,如#define keyscan P1 //程序中扫描信号从keyscan高4位输出， //键值返回信号从keyscan低4位读入， //故使用时硬件电路需要与之相对， //或者把软件中相应地方修改即可-/ / use : / / use the former post keyscan definition of SCM / / a port, keyscan such as # define P1
44scan
- //使用前请先定义keyscan为单片机的 //某个端口,如#define keyscan P1 //程序中扫描信号从keyscan高4位输出， //键值返回信号从keyscan低4位读入， //故使用时硬件电路需要与之相对， //或者把软件中相应地方修改即可-/ / use the former post keyscan definition of SCM / / a port, keyscan such as # define P1 / / scanning proces
KS0066U
- 单片机程序 单片机程序 单片机程序 -SCM procedures procedure SCM SCM procedures procedure SCM single procedure machine procedures SCM procedures procedure procedure SCM SCM procedures
ht6221
- 基于单片机的脉冲编码解码程序，应用单片机将脉冲编码解码成数据码-based SCM pulse codecs, application MCU will pulse codec into data code
NTServices
- VB NT 系统服务 scm -VB NT system services scm
12232LCDQUDONG
- 12232液晶单片机驱动程序源代码 -12232 LCD MCU driver source code 12232 SCM LCD driver source code
ds1624cprogram
- 由于DS1624是I2C总线结构的串行数据传送，它只需要SDA和SCL两根线完成数据的传送过程。因此，我们在进行程序设计的时候，也得按着I2C协议来对DS1624芯片数据访问。有关I2C协议参看有关资料，这里不详述。对于AT89S51单片机本身没有I2C硬件资源，所以必须用软件来模拟I2C协议过程。 要从DS1624中读取温度值，首先启动DS1624的内部温度A/D开始转换，对应着有相应的命令用来启动开始温度转换，有关DS1624的指令集参考前面的叙述。一般情况下，DS1624经过一次温度
dongsytem
- 嵌入式C编译程序(单片机)完整版高质量(按键 显示 坐标....)全译真正完整程序编译-Embedded C compiler (SCM), a complete version of high-quality (Press showed coordinates ....) Full Translation truly End the whole procedure compiler
C51LCDdisplay
- C51驱动LCD显示器的单片机程序。可以显示英文，数字-C51-driven LCD monitor SCM procedures. It shows in English, figures
P.H.Y_programer
- 单片机的程序集.大家可以参考一下.我想做一个更好的程序集及电路板.大约在10月份完成.请有兴趣的关注一下.当然我还要做一个通信的vhdl的仿真.-SCM suite. We can take a look. I would like to do a better procedures for collecting and circuit boards. About October completion. those interested in the look. of course, I sti
filter_51
- 单片机实现软件滤波 ，十种方法，介绍和源程序都有。-SCM software filtering, 10, and the source is introduced.
msp430&lcd
- ht1621 c源代码,使用msp43单片机-ht1621 c source code, the use of SCM msp43
Float
- 单片机浮点运算子程序,使用C51编程，可分别得到整数部分和小数部分,数据存储长度为4字节.-SCM floating point routines, the use of C51 programming, respectively integral part and be part of a minority, data storage for 4-byte length.
yejing11
- pic18单片机+128*64液晶显示程序-Pascal SCM 128 * 64 LCD procedures
f_calluate
- pic18F458单片机频率测量c程序，很好用-pic18F458 SCM c frequency measurement procedure is useful
Mod3
- 单片机AT89S52与计算机进行串行通讯,通过232进行,可以不停向PC发送-SCM At89s52 and computer serial communication, and by 232, could go to the PC Send
LCD12232-C51
- 使用1520控制器的12232点阵液晶模块的51单片机控制C代码,keil编译通过,使用端口直接连接方法,P1口为数据口,控制线在P3部分端口,详见程序.-1520 controller using the 12,232 dot-matrix LCD module SCM control of the 51 C code, c51 compiler, the use of ports directly connected, I P1 mouth of data, the Line of Cont
paomading
- 单片机应用 p1口八个灯作跑马灯。 8个灯依次点亮-SCM application p1 mouth eight lights for 5,250. Eight lamps were lit
data_vol_counter
- 数字电压表 利用单片机AT89S51与ADC0809设计一个数字电压表，能够测量0－5V之间的直流电压值，四位数码显示，但要求使用的元器件数目最少。 -digital voltmeter SCM AT89S51 ADC0809 design with a digital voltmeter, capable of measuring 0 - 5V DC voltage between the value of four digital display, but requires