搜索资源列表
adcmeter
- 基于 CS5550 工业测量仪表的设计:ADCMeter.ddb 中包含电路原理图和样品PCB图。本系统以 STC 系列 51 单片机为控制核心,使用高精度 CS5550 A/D 芯片来采集微弱的模拟信号量(如热电偶,热电阻信号量),可在线校准(零校准,满量程校准),校准数据保存到 93C46 中,作为以后 CS5550 运行的校准参数。本系统还包括两行八个数字位的数码管实时地显示采集数据,并可通过板上按键输入,进行输入信号变换的切换。另外还可增加串口通信部分,将采集的数据传输给上位机或其它控制
39-LCD160
- 一个stc单片机lcd程序例子,讲解了lcd的初始化,-A stc microcontroller lcd program examples to explain the lcd initialization
ADC_UART
- 本程序用STC-ISP Ver 3.0A.PCB的下载编程工具测试通过,相关的A/D转换结果在P1口上显示 -This procedure using STC-ISP Ver 3.0A.PCB download programming tools tested, the related A/D conversion results shown in the P1 port
stcEEPROM
- STC单片机,EEPROM操作 IAP_Disable //擦除扇区, 入口:DPTR = 扇区地址 void Sector_Erase(UINT add) 读一字节 字节编程-STC microcontroller, EEPROM operation IAP_Disable// Erase sector, entry: DPTR = sector address void Sector_Erase (UINT add) read a byte byte programmin
STC-chuar
- STC单片机 使用独立波特率发生器位波特率发生器,调试成功。共享给大家。-STC-bit microcontroller using a separate baud rate generator baud rate generator, debugging success. Share to everyone.
STCISPgggggghh
- 单片机 STC ISP 下载程序 好帮手-SCM STC ISP download a good helper
ad-2
- STC单片机中AD转换程序,可以作为模板运用-STC MCU AD conversion process can be used as a template
1602
- stc单片机的关于1602的驱动程序,需要的稍微改下就好了-stc microcontroller driver on 1602, need a little change like the following
12864j
- stc单片机的关于12864的驱动程序,需要的稍微改下就好了-stc microcontroller driver on the 12864, the need to change a little like the following
ds18b20
- stc单片机的关于ds18b20的驱动程序,需要的稍微改下就好了-stc microcontroller driver on ds18b20, needed a little change like the following
Ex19
- STC单片机,程序功能:开机后,LCD倒记时显示,开始LCD上显示9,1秒钟减1,直到减到0时,蜂鸣器响.停止。 学习重点: 1、模块间的交互 2、LCD、定时器的应用-STC microcontroller, the program features: boot, LCD countdown display, LCD display started by a 9,1 seconds, until reduced to 0, the buzzer sounds. Stop. Key
timebomb
- 制作一个基于AT89S52单片机的定时炸弹,包含程序设计的源代码,PCB图。-AT89S52 microcontroller based on making a time bomb, the source code of programming, PCB map.
PCA
- 应用STC单片机的PCA功能测量经测速装置输出的PWM方波的脉冲宽度,从而计算出速度,并用串口将速度数据发到计算机。-SCM application PCA STC function measurement device by the speed of the PWM square wave output pulse width to calculate the speed and the speed with a serial port data to the computer.
EEPROM
- 该程序实现了对STC单片机的EEPROM的操作。每隔0.5秒钟,单片机对EEPROM进行一次 读、擦除和写操作,并把数值显示到数码管上。 确认试验是否成功:电源上电后,数码管的值在递增,观察值。关闭电源,待几秒后上电, 数码管显示的值会从断电钱的那个值开始显示-The program realized STC microcontroller EEPROM operation. Every 0.5 seconds, the microcontroller on the EEPRO
qian
- 包装机仪表源码,使用ZLG7289显示带键盘,使用CS5460做AD转换,充分发挥了STC单片机的内部EEPROM。-Packaging machine meter source, use ZLG7289 display with a keyboard, use the CS5460 do AD conversion, give full play to the STC microcontroller' s internal EEPROM.
STC89
- STC头文件指的是采用C语言开发STC单片机时所需要的硬件定义文件,对于不同的单片机型号,头文件对应不同,其中主要定义单片机硬件的功能及接口。只有在头文件中做好了定义,才能对应上C语言程序与硬件之间的关系。 在C语言家族程序中,头文件被大量使用。一般而言,每个C++/C程序通常由头文件(header files)和定义文件(definition files)组成。头文件作为一种包含功能函数、数据接口声明的载体文件,用于保存程序的声明(declaration),而定义文件用于保存程序的实现 (
20080701
- STC单片机升级程序.作为一个手持仪用.从U盘读数据从串口输出,通过XMODEM协议.-STC SCM upgrade. As a hand-held instrument used. From the U disk read data from the serial output, through the XMODEM protocol.
MCU_m8
- c51,串口下位机通信程序,AD功能,STC单片机,带通信协议-c51, serial communication program the next crew, AD features, STC microcontroller, with a communication protocol
STC
- STC89C52是一种带8K字节闪烁可编程可擦除只读存储器的低电压,高性能COMOS8的微处理器,俗称单片机。该器件采用ATMEL搞密度非易失存储器制造技术制造,与工业标准的MCS-51指令集和输出管脚相兼容。-STC89C52 is a flash with 8K bytes of erasable programmable read only memory, low voltage, high-performance COMOS8 microprocessors, commonly know
LCD12864
- 利用STC单片机实现12864液晶屏显示中文字符,简单位图,驱动的读写-STC 12864 single chip using the LCD screen to display Chinese characters, a simple bitmap, the driver read and write