搜索资源列表
eff1
- 利用Verilog实现的跑马灯,从护栏管的一端循环到另一端。其他类似此类的循环语句基本一样。-Marquee achieved using Verilog, from one end of tube to the other end of the cycle. Other similar expressions of such basic, like the cycle.
NCVoltage
- 基于51单片机的数控直流电压源,8位数码管显示,输出电压范围0到14V-51 NC-based single-chip DC voltage source, 8-bit digital tube display, the output voltage range of 0 to 14V
clock
- 以前做的EDA课程设计,CLOCK,可设置时间的,6位数码管显示-Done before the EDA curriculum design, CLOCK, may set the time, digital tube display 6
shumaguan1
- 数码管的显示,动态显示,数码管显示两位以上-Digital tube display, dynamic display, digital display for more than two
HPA_PARAMETER_SETTINGS
- High Power Amplifier Modeling for TWTA(Traveling Wave Tube Amplifier) and SSPA (Solid-State Power Amplifier)
7289
- 7289的键盘显示程序,用于控制7289的按键,并在8位数码管上显示按键内容-Keyboard display program 7289, 7289 used to control the buttons, and 8 digital tube display key content
C51
- ME500单片机开发系统演示程序 - 8位数码管显示 */ /* */ /* 8位数码管从左至右显示 0-7 */ /* */ /* 版本: V1.0 (2006/11/20)-ME500 Single-chip systems demonstrate the development of procedures- an 8-bit digital tube display*//**//* 8-bit digital tube display from left to right
modian
- 模电关于单管共射的失真分析,用ewb连的。希望对你有帮助-Mode power on the shot a total of one-tube distortion analysis, even using the ewb. Want to help you
miaobiao
- 8位数码管秒表程序 用单片机C语言编程 八位数码管动态显示-8-bit digital tube stopwatch program with C language programming of eight single-chip LED dynamic display
test
- 一. 实验目的: 1.了解光电开关的使用方法 2.了解利用光电传感器测量电机转速的方法 二.光电测速基本原理 光电测速的基本电路由光电传感器、计数器和定时器组成。测量时在被测电机主轴上固定一个圆盘,圆盘的边缘上打上小孔。传感器的红外发射端和接收端装在圆盘的两测,电机带动圆盘转到有孔的位置时,红外光通过,红外接收管导通,输出低电平。红外光被挡住时接收管截止,输出高电平。用计数器记录在一定时间内传感器发出的脉冲个数就可以计算出电机转速。 三.实验内容 1.接线方法
daba
- 移动靶射击比赛 目的 (1)用8 个LED 发光管的来回滚动显示或跳跃运动显示来模拟靶的移动,用按1~8 数字键(对应8 个LED)来模拟射击,如果在某个LED 点亮期间按下相应数字键,表示射中并熄灯(全部熄),记录射中次数。 (2)比赛规则可有以下两种: 比赛规则1:靶始终来回不断地移动(一旦射中则从头开始滚动),在规定的时间(如50 秒)和规定的射击次数(如20 次)内看谁的射中次数多谁获胜; 比赛规则2:总共有若干个(如20 个)移动靶,每个靶的移动时间限制在一定的
measure_frequency_and_cycle_with_89C51_Microproces
- 用51单片机的定时器和外部中断分别实现对方波信号的高频测频和低频测周,同时将测量结果显示在LED数码管上,如果加外围加分频模块,可实现很高的精度和很高的频率测量范围-With 51 single-chip timer and external interrupt signals, respectively, to achieve the other side of the high frequency wave frequency and low frequency measurement we
Text1
- 计数器的设计,用七段数码管先是两位,满60进位。参考开发板程序-Counter design, digital tube first paragraph two, the age of 60 binary. Reference development board procedures
Digital_tube
- 基于keil与proteus仿真的数码管动态扫描显示-Proteus simulation based on keil and dynamic scanning of the digital tube display
123
- 用51内部定时器写的数码钟,数码管显示,新手上路,多学习一下-Using the digital timer write 51 internal clock, digital tube display
12425
- 通过按键控制中断,实现LED灯逐个点亮,然后将LED编码的十进制数在数码管上显示。-Through the button control interrupt, LED lamp lights, then one will be LED coded decimal number in digital display tube.
LED8_roating
- 使用KEIL环境μVision2版本,8段数码管循环显示0-F,共阳数码管,使用的单片机不同段表需要改变,此处用的是PHILIPS公司的P89V51,段表修改过以后可用于通用的C51单片机-KEIL environment μVision2 use version 8 digital tube display cycle 0-F, a total of Yang digital tube
ch451
- CH451的驱动函数库,采用16个按键,并控制8个数码管-CH451 driver library, the use of 16 keys, and control of 8 digital tube
adc0809
- 单片机控制adc0809做出的电压表。8路数字电压表可以测量0~5V范围内的8路输入电压植,并能在4位LED数码管上轮流显示。测量最大分辨率为0.01V,绝对测量误差约为±0.02V-Adc0809 made single-chip control voltage table. 8-channel digital voltage meter to measure the scope of 0 ~ 5V input voltage of 8-shik, and 4 in the digital t
8ludianziqin
- 数码管显示 1) 8个键盘(实现中音1~7和高音1共8个音),8位LED数码管可以记忆并显示最近8个按下的音,用喇叭送出按下的音。要求必须使用8255/8155扩展实现键盘和显示部分。 2) 长时间(如2s)按下某一键(可自己定义),可播放某一歌曲。 -Digital display 1) 8 keyboard (the realization of tenor 1 to 7 and a total of eight high tone), 8-bit LED digital tube