搜索资源列表
bujingdianjicheshi
- 4相步进电机测试程序，51单片机P1口，ULN2003驱动，实现正转反转-4-phase stepper motor test program, 51 microcontroller P1 mouth, ULN2003 driver Forward Reverse
xiyijidianji
- 双继电器模拟洗衣机电机控制 对应的继电器接口需用杜邦线连接到uln2003继电器控制端 通过控制2个继电器循环工作状态，模拟洗衣机间歇正反转 一般正转3s，停止2s，然后反转3s，停止2s，循环上述动作-Double the relay analog washing machine motor control relay corresponding interface requires DuPont line connected to the to uln2003 relay c
bujindianji
- 用单片机驱动ULN2003去控制步进电机。数码管旋转的角度会在数码管上进行显示。-MCU driver ULN2003 to control the stepper motor. Digital tube rotation angle will be displayed on the digital.
MSP430
- 采用MSP430单片机对步进电机的控制，通过I/O口输出的时序方波作为步进电机的控制信号，信号经过芯片ULN2003驱动步进电机；同时，用 4个按键来对电机的状态进行控制，并用数码管动态显示电机的转速。-Using MSP430 microcontroller stepper motor control, through the I/O port output timing square wave as stepper motor control signals, the signal afte
Downloaded-Data-Sheets
- max220-max249.pdf；mm74hc373.pdf；ads7824.pdf；uln2003.pdf相关的资料-max220-max249.pdf mm74hc373.pdf ads7824.pdf uln2003.pdf relevant information
zidongshangshui
- 基于51单片机和uln2003的水位显示自动上水系统-51 And uln2003 based on the level indicator automatic water system
jidianqi
- 基于单片机独立按键控制继电器开关。对应的继电器接口需用杜邦线连接到uln2003继电器控制端-Microcontroller-based independent keys control the relay switch. DuPont corresponding relay interfaces required cable to uln2003 relay control terminal
dianjizhengfanzhuan
- 这是一个基于STC89C51和ULN2003的步进电机正反转的驱动程序，通过STC89C51控制ULN2003的正反转-This is a STC89C51 and the stepper motor ULN2003 driver ULN2003 reversing control via STC89C51
Disinfection-clean-screen-program
- 医院里空气净化器主芯片的主程序，主要芯片有STC89C54RD+，DS1302，ULN2003。-Hospital air purifier main chip of the main program, the main chip has STC89C54RD+, DS1302, ULN2003.
jingzhunbujindianji
- 1，ULN2003步进电机驱动芯片 2，MCU STC89C52 3，高精度四相步进电机 显示效果： 1，通过简单延时控制电机转动-1, ULN2003 stepper motor driver chip 2, MCU STC89C52 3, four-phase stepper motor precision display: 1, by simply turning the control motor delay
shumaguanxianshibujindianjijiaodu
- 用单片机驱动ULN2003去控制步进电机。 数码管旋转的角度会在数码管上进行显示-Drive ULN2003 MCU to control the step motor. Digital tube rotating Angle will be conducted on the digital tube display
ULN2003
- MSP430F149+UL2003驱动电机，可以正反转，程序亲测并使用-MSP430F149 UL2003 drive motor can be positive, pro-test program and use
motor2
- Verilog编程实现步进电机的单双八拍的四路脉冲信号。采用28BYJ-48步进电机（驱动ULN2003）验证可以实现其正反转。-Single and double eight four-shot pulse signal Verilog Programming stepper motor. Using 28BYJ-48 stepper motor (driver ULN2003) verification can achieve its inversion.
ULN2003
- 高耐压、大电流复合晶体管IC—ULN2003ULN2003 -ULN2003ULN2003
stepmotortest
- 最近做的工程需要用到步进电机,但由于量小,又没有厂家的选型手册,只得托人从深圳随便发了几个……NMB （PM35L-048-HPH7）据我的测试，在单四排工作模式下，其步进角为7.5度。驱动模块用的是ULN2003,只用了四个单元，接口用的是P3,当然程序里面把P1也定义了，在我的测试板上，P1是接LED指示单元的，只是为了调试方便而以-err
Stepper-motor
- 用单片机驱动ULN2003去控制步进电机，数码管旋转的角度会在数码管上进行显示。-MCU ULN2003 to drive stepper motor control, digital control rotation angle will be displayed on the digital pipe.
zhiliudianjitiaosukongzhi
- 对应的电机接口需用杜邦线连接到uln2003电机控制端使用5V-12V 小功率电机皆可 2个按键分别加速和减速-DuPont required corresponding motor interface cable to uln2003 motor control side using 5V-12V low-power motors can be two keys are acceleration and deceleration
monixiyijikongzhi
- 对应的继电器接口需用杜邦线连接到uln2003继电器控制端通过控制2个继电器循环工作状态，模拟洗衣机间歇正反转一般正转3s，停止2s，然后反转3s，停止2s，循环上述动作-DuPont corresponding relay interfaces required cable to uln2003 relay control terminal loop by controlling two relays working condition, washing machine intermitten
bujindianjiceshi
- STM32奋斗板步进电机测试,演示的是通过C口的4个口线利用tim2定时器，固定周期产生4路的脉冲信号模拟步进电机的4相8拍控制组合。步进电机采用型号为5V 28BYJ-48的步进减速电机。步进角 5.625度/64驱动板采用ULN2003驱动板。-STM32 struggle board stepper motor testing, demonstration by four port line C port utilization tim2 timer, fixed cycle 4 puls
StepMotor
- 步进电机驱动程序，驱动芯片用的是ULN2003,5线4相制步进电机。-StepMotor Control Driver Program.