搜索资源列表
AVR_IMU_1
- 卡尔曼滤波在AVR单片机的应用，引脚接法：PC1 (ADC1) Y Accel (Pin 8) PC2 (ADC2) Z Accel (Pin 7) PC3 (ADC3) X Rate (Pin 3) PC4 (ADC4) Y Rate (Pin 4) PC5 (ADC5) VRef (Pin 5) - Currently, this project assumes the AVR ATmega168 MCU is hosted on the AVR STK5
ADC0
- 2812 ad 程序 详细介绍ad的使用和用法 ，是非常不错的选择。 -2812 ad ad program details the use and usage, is a very good choice.
ADC0_TEMP
- 8051F单片机：实现ADC0采样芯片温度，通过LCD显示，并通过串口0（J13）发送到PC机。-8051F SCM: Achieving ADC0 sampling chip temperature, through the LCD display, and through serial 0 (J13) sent to the PC.
UART0
- ADC0采样芯片温度通过LCD显示，并通过串口0（J13）发送到PC机,同时接收PC传回的一个字符并显示， 请使用串口调试工具调试！-ADC0 sampling chip temperature through the LCD display, and through serial 0 (J13) is sent to the PC, at the same time returns the PC to receive a character and display, use the s
ADC0_TEMP
- ADC0采样芯片温度，通过LCD显示，并通过串口0发送到PC机-ADC0 sampling chip temperature, through the LCD display, and through serial port 0 is sent to the PC machine
AD-LCD
- 实现如下功能： 调节ADC0的可变电阻时，当输入电压小于1.1V时，LCD 显示红色，当输入电压在1.1~2.2V时，LCD显示绿色，当输入电压大于2.2V时，LCD显示蓝色,同时串口输出电压值。 -To achieve the following functions: regulating ADC0 variable resistor, when the input voltage less than 1.1V when, LCD display red, when the inpu
adc_1602
- LCD1602来显示通过AVR ADC0采集的信号，参考电压为ACC，上下浮动不超过0.2V-LCD1602 to show through the AVR ADC0 collected signal, the reference voltage for the ACC, plus or minus no more than 0.2V
ADC0--5
- AD 转换 数码管显示 0到5V ad0804-AD0804 7segment 0 to 5 V
adctoportd
- READ ABOUT ADC0 CHANNEL IN PIC18F452 AND WRITE DE RESULT IN PORTD
ADC0
- 本程序使用C8051F020单片机自带的数模转换，将单片机内温度传感器的温度进行AD转换。-C8051F020 single chip uses the built-in digital-to-analog conversion, to single-chip temperature sensor AD conversion temperature.
ADC_FOR_EASYARM1138
- easyarm1138上ADC采样程序，通过处理器直接触发ADC采样，ADC模拟量需从外部输入（ADC0），最大不能超过3.0V，因为ADC内置的参考电压为3.0V-easyarm1138 on the ADC sampling procedures, directly through the processor to trigger ADC sampling, ADC analog input from the external (ADC0), the largest not more tha
ADC0_TEMP
- C8051F020实现ADC0采样芯片温度，通过LCD显示，并通过串口0（发送到PC机-ADC0 sampling C8051F020 chip temperature to achieve, through the LCD display, and through the serial port 0 (sent to the PC machine
UART0
- C8051F020实现ADC0采样芯片温度，通过LCD显示，并通过串口0（J13）发送到PC机,同时接收PC传回的一个字符并显示，请使用串口调试工具调试！-ADC0 sampling C8051F020 chip temperature to achieve, through the LCD display, and serial 0 (J13) is sent to the PC, at the same time to receive a return PC and display the
adc0
- hertv hlkertbm rwel tbn- n , tryuoo
UART0_usb
- c8051f020 实现ADC0采样芯片温度，通过LCD显示，并通过串口0再经过CP2102芯片“UART-USE”（J19）发送到PC机, 请使用串口调试工具调试-c8051f020 to achieve ADC0 sampling chip temperature, through the LCD display, and through the serial port 0 go through CP2102 chip, " UART-USE" (J19) sent
C8051F020-UART0_usb
- C8051F020单片机USB驱动程序例子，实现ADC0采样芯片温度，通过LCD显示，并通过串口0再经过CP2102芯片“UART-USE”（J19）发送到PC机。-C8051F020 MCU USB driver for example, to achieve ADC0 sampling chip temperature, through the LCD display, and through the serial port 0 go through CP2102 chip, " U
ADC
- 在c8051f020上实现ADC0的采样，以及各个寄存器配置-The c8051f020 achieve ADC0 sampling, and various configuration registers
LedFlash3
- 该程序主要是ATmega88 A/D转换程序的演示。当通道ADC0(PC0)上的电压大于2.5V时，LED开始闪烁！-The program is mainly ATmega88 A/D conversion process of the presentation. When the channel ADC0 (PC0) is greater than 2.5V when the voltage, LED start blinking!
4
- 实现ADC0采样芯片温度，通过LCD显示，并通过串口1（J13）发送到PC机-this programme can realize the chip temperature sampling ,and displayed on the lcd, then sent to the PC through the J13.
adc0
- 51单片机初学者，这段程序将简单应用ad，容易学习-good