搜索资源列表
F12x_ADC0_ExternalInput
- c8051f120单片机使用12位ADC0测电压例程1,带说明-c8051f120 single chip using 12-bit ADC0 voltage measurement routine one, with a note
F12x_ADC0_ExternalInput_Mux
- 单片机c8051f120使用12位ADC0测电压例程2,带说明-SCM c8051f120 measured using 12-bit ADC0 voltage routine 2, with instructions
ADC0
- 液晶显示,完整的液晶显示程序,希望对大家有帮助-LCD DISPLAY
F020ADC
- F020单片机的ADC0采样程序(使用中断)-F020 MCU ADC0 sampling procedures (using interrupts)
020ADC0_Buf1
- 使用020的定时器3来实现ADC0的中断模式-This program shows an example of using ADC0 in interrupt mode using Timer3
3-6
- c8051F040 ADC0监控中断调试程序-c8051F040 ADC0 interrupt monitor debugger
Temperature(ADC0)
- 一个利用ADC的温度测量程序,经过ADC模块可以将模拟信号换成数字信字,又叫数温度计-A temperature measurement procedure using ADC, after ADC module can replace the analog signal digital letter words, also known as the number of thermometer
lm3s1138_adc
- 基于《Stellaris外设驱动库》的例程:处理器直接触发ADC采样 本实验演示配置ADC采样序列0,通过处理器直接触发ADC采样,ADC模拟量需从外部输入(ADC0),最大不能超过3.0V,因为ADC内置的参考电压为3.0V。 在进行ADC配置之前,必须首先进行PLL锁相环配置(详见EasyARM1138例程\02 SysCtl(系统控制)\3 锁相环PLL设置)。错误配置PLL将使系统进入异常。 ADC采样得到的数字量将利用超级终端从串口读出 。本开发板采用US
ADtoPC
- C8051F340测量电位器的电压值,AD采样后通过数据串口传到上位机-This example code takes and averages 2048 analog measurements from input P1.1 using ADC0, then prints the results to a terminal window via the UART
ADC
- 采集外部模拟电压,采用ADC0通道0,内部VREF,并显示于LED上.-External analog voltage acquisition using ADC0 channel 0, the internal VREF, and displayed on the LED.
qq
- AD转换 实现C8051F120的ADC0模拟采集 源程序-AD convert the ADC0 achieve C8051F120 analog capture source
single
- 基于C8051F040的C语言编写单端输入,定时启动,由T2定时,选择AIN0.3为ADC0转化通道-C8051F040 C-language based on single-ended input, timer start, by the T2 timer, select the ADC0 conversion channel AIN0.3
adc0
- 是关于ADC0832芯片的adc转换程序-this is a about adc0832 convert it is a very useful source
AdcToPwm
- Captura una señ al análoga conectada en el ADC0, y la traslada a la salida PWM0 (PD0). La resolución del generador PWM0, se ajusta a 10 bit según la constante ctPwmCounts, sin tener en cuenta la frecuencia portadora de PWM, esto para igualar
PwmChipMpd
- Captura una señ al análoga conectada en el ADC0, y la traslada a la salida PWM0 (PD0). La resolución del generador PWM0, se ajusta a 10 bit según la constante ctPwmCounts, sin tener en cuenta la frecuencia portadora de PWM, esto para igualar
AD_TEST
- 本文件是AD测试实验;测试前需要对管脚复用的电压基准进行设置,将JP10的2,3脚短接,1脚空出。AD输入端子(J10)可输入4路AD(ADC0--ADC3),另有1路可测量片内温度,5路采样值都通过串口发送出去,在串口调试助手上看观察其值。4路AD中ADC0可通过跳线器(JP5)“ADJ_VOL”(1,2脚短接)与板上电位器相连,通过手动调VR1可以观察到电压值的变化-This document is the AD test experiment testing is required be
AD
- AD差分通道采样,通过ADC0和ADC1进行差分电压的显示。-AD differential channel sampling
ADC0
- lm3sxxx系列adc源码,软件环境 Keil,语言为单片机c语言-lm3sxxx series adc source, software environment Keil, language, c language for the microcontroller
STC12C5A60S2-ADC
- STC12C5A60S2系列的ADC口编程实例,此程序只写了ADC0口的转换,其他口可一次类推-STC12C5A60S2 series ADC port programming examples, this program is only written ADC0 conversion of mouth, other mouth at once and so on
C8051adc
- 使用C8051F020的内部ADC0,测量外部电压,八个通道都可以测量,并通过液晶显示测量值。-Using the C8051F020 internal ADC0, measuring external voltage, eight channels can be measured, and the LCD display of measured values.