搜索资源列表
CANTest
- 使用TMS430F149进行GPS数据接收以及CAN总线控制的例子。-Using TMS430F149 GPS data receiver and CAN bus control example.
CANSF
- 基于CAN总线数据发送与接收,利用sja1000芯片进行数据发送与接收-based on CAN data send and receive
C8051F50xCAN
- C8051F50x系列的单片机关于CAN总线开发系统的发送和接收程序-The receive and transimit programs of CAN-BUS in C8051F50X
CODE-Easy2812
- CODE-Easy2812开发板源程序 5.1 内部定时器0实验 5.2 内部定时器2实验 5.3 事件定时器实验 5.4 数码管显示实验 5.5 蜂鸣器控制实验 5.6 外部RAM读写实验 5.7外部FLASH读写实验 5.8 GPIO控制实验 5.9外部中断控制实验 5.11 RS-232串口通讯实验 5.13 CAN总线接口实验 5.15 直流电机控制实验 5.16 步进电机控制实验 5.17 12864液晶显示实验 5.18 1
canbus
- CAN总线驱动。使用的can芯片是MCP2510 使用的是标准帧,模拟SPI时钟信号,能够实现数据的发送,接收。-CAN bus driver. USing MCP2510 chip, and the standard frame, the simulation SPI clock signal, can realize data to send, receive.
CAN_RECEIVE
- 该程序可实现CAN的接收,程序基于XEP100芯片。 CAN是控制器局域网络(Controller Area Network, CAN)的简称,是由研发和生产汽车电子产品著称的德国BOSCH公司开发了的,并最终成为国际标准(ISO118?8)。是国际上应用最广泛的现场总线之一。 在北美和西欧,CAN总线协议已经成为汽车计算机控制系统和嵌入式工业控制局域网的标准总线,并且拥有以CAN为底层协议专为大型货车和重工机械车辆设计的J1939协议。-The program can realize th
B-MCP2515-receive-onebyte-125kbps
- 通过CAN总线接接收一字节数据再串口转发出去 功能描述:CAN通信测试程序,CAN中继器的功能 IDE环境: keilC Init2515: 2515初始化程序 CAN_ Send: CAN发送子程序,查询发送 CAN_Receive:CAN接收子程序,中断接收 硬件连接: AT89S51/52+MCP2515-Via CAN bus interface receives a byte of data and then forwarded out the seria
ButtonA-sends-a-byte-temperature
- 通过CAN总线将该节点采集的温度数据发送出去 CAN总线环境温度采集 按键控制发送 IDE环境: keilC CAN_ Send: CAN发送子程序,查询发送 CAN_Receive:CAN接收子程序,中断接收 硬件连接: AT89S51/52+MCP2515+DS18B20-Temperature data sent via the CAN bus node collection CAN-bus controlled ambient temperature ac
Button-sends-8-bytes-of-data
- 通过CAN总线将b[8]={0x01,0x02,0x03,0x04,0x05,0x06,0x07,0x08}发送出去 CAN通信测试程序,CAN中继器的功能 IDE环境: keilC 2515初始化程序 CAN发送子程序,查询发送 CAN接收子程序,中断接收 硬件连接: AT89S51/52+MCP2515-Via CAN bus b [8] = {0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07, 0x08} sent CAN
CAN
- 汽车嵌入式工程中配置CAN局域网总线单片机的底层通用的程序。初始化收发器、CAN接收和发送中断等等。-Automotive embedded engineering LAN configuration CAN bus microcontroller underlying common procedure. Initialization transceiver, CAN receive and transmit interrupt and so on.
Example_281xECanBack2Back
- DSP2812 CAN总线 无中断例程源码,包括发送和接收-2812 CAN bus without interruption routine,
SourceCode13_ecan_back2back_OK
- DSP28335 CAN总线模块,32个邮箱自动接收与发送-DSP28335 CAN bus module 32 automatically receive and send mail
VC-interface
- 这是用VC编写的一个界面,用于水下机器人的数据传输,可通过CAN总线进行数据的发送和接收。-an interface
CAN_FIFO
- stm32开发板can总线源码,有接收还有发送-stm32 development board can bus Source
03_CAN-communication(Two-STM32-chip)
- 1、STM32 CAN总线下的双机数据互传 2、如果需要同时发送数据需要修改程序(CAN初始化内要设置为可以自动重传,否则会因为总线仲裁,某个STM32无法完成数据发送) 3、需要配备CAN接收发控制器,例程中采用的是TJA1050-1, dual-data STM32 CAN bus pass each other under 2, if need to send data at the same time need to modify the program (within CA
AT90CAN128
- at90can128,can总线通讯编程。初始化设置,发送程序。接收中断子程序。-At90can128, can bus communication program. Initialization Settings, router. Receiving interrupt subroutine.
DSP281x_ECan
- DSP2812处理器硬件Can总线处理,可自动设置多种通信波特率,包含发送接收程序-DSP2812 processor hardware Can bus, Can automatically set various communication baud rate, include to send and receive procedures
up_MSP430-mcu-CANbus
- MSP430单片机CAN总线程序的发送与接收例程-MSP430 MCU CAN bus procedures to send and receive routine
can_test
- 源码为can总线环回测试程序,使用stm32f103c8t6单片机。can接口接入单片机PA11和PA12管脚,串口1(PA2,PA3)打印接收到的数据。源码中使用定时器3计时,每5s发送一次数据,在can中断接收据,在while程序中将接收到的数据打印出来。-Source code for can bus loopback test program using stm32f103c8t6 microcontroller. It can interface to access the micro
CAN_communication
- CAN总线通信,总线发送接收,中断接收函数-CAN communication