搜索资源列表
doubleloop
- 电流电压双闭环的PI单相逆变器仿真,自己做的,请指教-Double closed loop PI current and voltage single-phase inverter simulation, make their own, please advise
avgmodepfc
- 用MATLAB M语言实现平均电流模式控制的PFC数学模型。运行该程序后可看到电流,电压波形。-Using MATLAB M language to achieve an average current-mode PFC control, mathematical model. After running the program to see current and voltage waveforms.
libsynk-current
- Libsynk library for gtsnets.
current
- 一些关于恒流源的资料,那里有电路原理图,用的着的话就拿去吧。-Some information on the constant current source, where the circuit schematic diagram, if used in the case go forward.
FAN7888
- 该 FAN7888 是一款集成了三个半桥式栅极驱动器集成电 路的芯片,专为高压,高速驱动MOSFET和 IGBT设计, 可在高达 +200V电压下工作。 飞兆半导体的高电压处理和共模噪声消除技术可以保证高 端驱动器在高 dv/dt 噪声环境下稳定工作。 先进的电平转换电路允许高端驱动器在 VBS=15V 时运行 在 VS=-9.8V(典型值)。 当 VDD 和 VBS 低于指定的阈值电压时, UVLO 电路能够 预防故障。 输出驱动器的拉电流 / 灌电流
srm_c7
- 开关磁阻电机的速度控制程序,电流用的是滞环控制,控制器采用TI公司的DSP TMS320LF2407,开发环境采用TI提供的CC2000或者CCS-Switched Reluctance Motor speed control procedures, using current hysteresis control, the controller using TI
current
- 采用matlab软件进行的移相全桥仿真研究(恒电流)-Carried out using matlab software simulation of phase-shifted full-bridge (constant current)
short 短路电流计算MATLAB程序
- 短路电流计算MATLAB程序,适合电力系统分析学习-Short-circuit current calculation MATLAB program for power system analysis study
sanxiangnibianGTO
- 基于pscad实现的三相电流源型逆变器,GTO-Based on pscad for three-phase current-source inverter
Current
- 1、数控直流恒流源的单片机代码。 2、重要包括电源、输入处理、A/D采集、键盘、LCD显示、D/A输出。-1, numerical control of single-chip DC current source code. 2, it is important to include the power supply, input processing, A/D acquisition, the keyboard, LCD display, D/A output.
ansoft
- ansoft eddy current viedo post calculation
current
- 在工业控制交流采样中的零线电流计算方法-AC sampling in the industrial control of the zero line current calculation method
jakarta-taglibs-standard-current
- 此文件是关于流的应用 -This file is on the application of flow
motor
- 三相异步电机直接起动的起动转矩较大,但起动电流也大,通常用于小功率电机。-Three-phase asynchronous motor starting torque direct start a larger, but the starting current is also large, normally used for low-power motor.
current_controller
- Current controller for inverter
boost_PCM_line_reg
- 基于平均法的断续模式下buck,boost,buck_boost型DC/DC功率级建模步骤,包括电压模和峰值电流模-Based on the average method of discontinuous mode buck, boost, buck_boost type DC/DC power level modeling steps, including the voltage mode and peak current mode
EnergyMeter
- Energy meter To measure the voltage and current
water11.11
- 使用MSP430F413的低功耗水表系统,在空闲时电流3.5uA-The use of low-power meter MSP430F413 system idle current 3.5uA
NCDCcurrentsource
- 采用51系列单片机为控制核心,包括电源变换处理及分配模块,恒流源模块,单片机主控模块,键盘输入模块,LCD显示模块,数模/模数转换模块,语音模块和实时时钟模块的9个部分。通过键盘设定好需要输出的电流值后,单片机对设定值按照一定的算法进行处理,经数模输出电压控制恒流源电路输出相应的电流值-51 Series single-chip microcomputer used for the control of the core, including the processing and distrib
DynamicPowerQualityTestingTechnology
- 本文首先介绍了有源电力滤波器的基本结构和工作原理,并对一些常规的谐波电流检测方法的优缺点进行了比较。其次,针对传统的谐波电流检测方法的缺陷,提出将神经网络与基于噪声抵消原理的自适应谐波检测相结合,利用径向基函数运算量小、收敛快、无局部极小值等优点,构造了一种基于径向基函数神经网络的谐波电流检测方法,仿真结果表明该检测方法具有很好的动态响应及畸变电流检测精度。最后,设计了一套实验系统,对本文所采用的系统方案进行了实验验证。仿真表明,本文所采用的有源电力滤波器检测系统方案切实可行,能够较好地实现动态