搜索资源列表
led
- 设计一套8位 LED 灯控制系统，要求如下： （1）自动循环实现所有功能，自定义功能选择开关。 （2）有四种状态可供选择-Design a set of eight LED lamp control system
the-test-about-USB-light-up-LED
- 一个通过USB端口去控制LED灯亮的MFC软件-A MFC software that can control LED lighter through USB port
a-firmware--USB-light-up-LED-
- 用于通过USB点亮LED灯的USB固件程序-a firmware used to a test about USB light up LED
FPGA-code--USB-light-up-LED
- 一个通过USB端口去控制LED灯亮的FPGA源码-a FPGA code used to a test about USB light up LED
LED
- 并不是简单的LED灯闪烁，而是结合实际将制作的单片机版的LED灯进行交叉闪烁-And is not a simple LED lights flashing, but actual will make single-chip version of the cross and LED lights flashing
led_PWM_c51
- 该源码是通过单片机实现PWM调节LED灯的亮度- The source is the microcontroller PWM dimming the brightness of the LED light
LED
- 七段LED显示电路的设计，很好的利用数码管，达到LED灯的亮与灭。-These seven LED display circuit design, good use of digital tube, reach the light of LED lights and destroy.
led
- 本程序演示了单片机对各个io的控制,控制led灯的亮和灭-This program demonstrates the control of the microcontroller for each io control led lights turn on and off
led
- led灯模拟电梯走法 经测试可运行，无按键锁存功能-A led game like a floor.
vb-led
- 上位机编写vb程序控制89c51单片机上led灯-vb led tada
led
- 基于51单片机实验板设计原理图及led灯测试c代码-Based on 51 single-chip board design schematics and led light test c code
add-and-difference-led
- 计算两数的和与差，并判断其是否相等，相等则点LED灯-Calculaqting the sum and the difference of two numbers, then judge whether the sum equals to the difference, if equals, the LED is lighted(by liang yu,yz universi..)
led
- 博创S3C2410点亮3盏LED灯的汇编代码-The ASM Code of the base experience using UP-TECH S3C2410 to light 3 leds.
LED
- fpga中实现简单的led灯控制，包括流水灯等一系列的程序，帮你玩转led-led control
LED
- LED灯的应用，接着是实现流水灯的效果，程序不断修改，可以实现不同的流水效果-The application of LED lights, followed by the effect of light water, is continuously changing, and different water
1.LED
- 利用cc2430芯片实现LED灯的流水显示-Using CC2430chip to realize LED light shows
KEY-LED
- 基于STM32F103XX单片机的按键控制LED灯程序-To control the LED light program key microcontroller-based STM32F103XX
led
- s3c2410ARM板上的led驱动程序 用它可以驱动led灯的变化-s3c2410ARM panel LED driver can drive led light changes
led
- LED闪烁程序利用IO口来控制板上LED灯的亮和灭，使用的是CORTEX-M3核心板和lm3s6965的MCU，在keil中编译下载即可运行。-Flashing LED program uses IO port control board LED lights turn on and off, using the CORTEX-M3 core board and lm3s6965 MCU, the keil compiler download to run.
key-led
- 按键程序通过IO口来读取按键的状态，并根据读取的键值用IO口来控制led灯的亮和灭，使用的是CORTEX-M3核心板和lm3s6965的MCU，在keil中编译下载即可运行。-Key program through the IO port to read the button state, IO port read key to control the led lights turn on and off, using the CORTEX-M3 core board and lm3s6965