搜索资源列表
LED
- easy1138开发板LED灯闪烁开发程序-easy1138
led-6
- 主要是工作在minicom环境下，编写驱动程序，家在字符设备模块，是S3C2410开发板上的LED灯变亮和变灭。-Mainly working in minicom environment, write drivers, character devices in the home module is S3C2410 development board LED lights brighten and change out.
IOCtrl.tar
- mini2440/TQ2440 LED灯亮灭的控制软件，Qt源码-mini2440/TQ2440 LED control software (source), designed with Qt
LED
- 这个程序是一个关于led灯闪烁的，用的是labview9.0来编写的，这是一个通用的程序，仅供大家参考-This program is a flashing led lights is labview9.0 to write, this is a common procedure for your reference
led
- arm板上led灯的驱动程序开发，点亮或熄灭-arm board led lamp driver development
STM3-LED-ucos
- 基于uCOS-II的控制LED灯的闪烁；基于奋斗版STM32开发板-Based on uCOS-II,it can controling the flash of LED.
PWM-control-LED-more
- 单片机定时器产生一个PWM波，控制LED灯的亮灭程度。-Microcontroller timer generates a PWM wave to control the degree of bright LED lights off.
OK6410A-LED-Marquee-Button-Driver
- 开发板OK6410A，LED灯和按键驱动程序！-Development board OK6410A, LED lights and buttons driver!
led
- DSP的一个测试程序，LED灯的显示，可以在DSP的开发环境下运行，已测试过，可以使用-DSP a test program, display of LED lights, you can run in the DSP development environment, has been tested, you can use
EM310-control-LED
- 一个关于EM310用法的历程，主要功能是可以通过EM310用短信远程控制LED灯，附图，学习EM310远程控制的朋友可以参考下-About the the EM310 usage of course, the main function is through EM310 SMS remote control LED lights, friends can refer to the following drawings, learning EM310 remote control
LED-dynamic-testing
- eda实验资料，led灯动态扫描实验，有完整的图及程序-eda experimental data led lights dynamic scanning experiments, complete plans and procedures
led
- led灯显示屏幕：显示屏的控制电路接收来自计算机的显示信号，驱动LED发光产生画面，并通过增加功放、音箱输出声音。 -led lights display screen: display control circuit receives the display signal from the computer, the drive LED light screen, and by increasing the amplifier, speakers output sound.
LED
- 红外遥控LED灯，汇编语言红外程序解码，控制LED亮和灭，对初学者有很大帮助。-Infrared remote control LED lamp assembly language IR program decoding, the control LED turn on and off, a great help for beginners.
PWM-charge-LED
- PWM控制LED灯渐亮渐灭，适用于51单片机，简单易行。-PWM control of LED lights getting brighter gradually eliminate, suitable for 51 microcontroller, is simple.
LED
- stm32 arm7控制led灯，跑马灯实验程序-the stm32 control led, Marquee experimental program
LED
- 主要功能和技术指标要求： 1. LED灯外接于P0.0端。 2. LED灯分别按2Hz，1Hz和0.5Hz三种不同频率闪动，各持续10s。 3. 在LED灯开始和停止闪烁时蜂鸣器分别鸣响1次。 4. 利用单片机内部定时器定时，要求采用中断方式 -The main features and technical requirements: 1 LED lights external P0.0 end. 2. LED lights press 2Hz flashing 1Hz an
LED-verilog
- 利用verilog语言点亮led灯，基于2410开发板-The use of the verilog language lights led lights, based on the 2410 development board
LED
- LED灯流水显示，形成跑马灯的形式，从左到右依次点亮，至一排全部显示，再熄灭，如此重复-LED light water show, the formation of the form of the Marquee, lit from left to right, to a row of Show All, and then goes off, so repeat
LED
- FPGA VHDL实现 点亮LED灯 VHDL实现-FPGA VHDL lit LED lights VHDL implementation
LED
- 流水灯的源程序在Keil软件中可以打开，实现LED灯的流水控制。-Light water source in the Keil software can open, LED lights, water control.