搜索资源列表
dm642main
- 可以将开发板上的LED灯点亮的一个小程序(a small program of what can be developed on the board of LED lights lit)
Template 流水灯实验
- 基于STM32的led流水灯实验源码，需要在对应平台使用(Based on STM32 led lamp experimental source, you need to use the corresponding platform)
实验1 - GPIO输出控制LED
- 配置NRF51822的I/O口实验，用I/O控制LED灯(allocation; configure; collocation; deploy)
LED_200T
- 本工程包含了一个LED灯测试程序，可以任意更改测试模式。(This project contains a LED lamp test program, you can change the test mode at any time.)
LEDPID
- 用光敏电阻PID控制LED灯，显示屏用的OLED(Control LED lamp with photosensitive resistor PID, OLED used for display screen)
LED
- 单片机led灯点亮，从左到右点亮52单片机上的LED灯(Lit LED lights, lit from left to right, a simple program)
main
- 根据STM32寄存器地址，配置P0~P3为推挽输出，点亮LED灯。(According to the STM32 register address, the configuration P0~P3 is push-pull output, and the LED lamp is lit.)
LED_blinking
- LED灯闪烁程序 提供修改和测试软件接口(LED blinking: --USER --SYSTEM --OBJECTS)
Documents
- 51单片机LED灯()
5.接收短信控制LED灯
- 1、板子上电后运行指示灯RUNING_LED会以一秒的频率闪烁； 2、通过芯片的串口1可以监视模块的登录情况； 3、手机发送“onled”点亮LED； 4、手机发送“offled”熄灭LED； 5、使用串口2与模块通信，串口1用于将信息打印输出。(1, after the board power, the operating indicator RUNING_LED will flicker at a frequency of one second; 2, through the ch
AT89C51
- 这是型号为AT89C51单片机与由32个LED灯组成的心形电路，接通电源后，LED按 程序依次点亮，变换成心形图案。(This is an AT89C51 single-chip microcomputer with 32 LED lights, and the LED is turned on by the program and transformed into a heart shape.)
实验4：系统时钟
- 自定义RCC系统时钟，通过改变其倍频与分频实现延时时间变化，实现LED灯闪烁效果。(Customize the RCC system clock, by changing its multiplier and frequency to achieve delay time changes, to achieve LED light flashing effect.)
跑马灯
- 用51单片机实现对使用LPD6803芯片的LED灯带进行控制，实现跑马灯。(With 51 MCU control with the LED lamp using LPD6803 chip, to achieve marquee.)
PCF8591(矩阵按键控制led亮度)
- 这是我自己编写的PCF8591程序，本程序可以使用msp430单片机的矩阵键盘来控制pcf8591模块上led灯的亮度，从0~255可调，输出电压也可调。(This is my own written PCF8591 program, this program can use the MSP430 microcontroller matrix keyboard to control the pcf8591 module on the brightness of LED lights, adjus
点亮LED
- 基于stm32f103系列开发板顺序点亮LED灯，实现跑马灯效果(STM32F103 series development board based on the order of the LED lights, to achieve marquee effect)
C51交通灯
- 用LED作为信号灯模拟交通灯 南北方向道路绿、黄、红灯亮时间分别是60s、50s、10s 东西方向道路绿、黄、红灯亮时间分别是60s、50s、10s、(Use LED as a signal light to simulate traffic lights North and south direction, road green, yellow, red light, respectively, 60s, 50s, 10s East and west directions, green
LED_PC13
- 控制PC13口的LED灯闪烁,可以用来测试STM32模板是否能使用。(The LED light that is controled by the PC13 port flashes)
Exe
- 实现msp430的led灯亮灭，就是这样用iar编程下载程序(MSP430 lights to achieve LED lights out, that is, using IAR programming download program)
01.外设-LED
- nrf1822工程temp,学习适合，点亮了led灯(Nrf1822 engineering temp, learning suitable, lit the LED lights)
LED
- 流水灯的简单实现，基于FPGA的实现，包含管脚分配文件等(realize the function of waterfall light based on FPGA.)