搜索资源列表
EEPROM 93C46測式程式
- 將table[]的資料寫入到93C46中,然後再把資料由93C46讀出送到P1去由LED來顯示之,如此週而復始,不斷的重複寫入與讀出(93C46的重複寫入壽命約一萬次) 就可以看到P1的LED由P1_7到P1_0依照順序的ON/OFF
LHW214EH.pdf
- 功率型光电继电器,具5000耐压隔离电压.负边双向导通-The LHW214EH consists of an AlGaAs infrared light-emitting diode (LED) input stage optically coupled to a high-voltage output detector circuit. The detector consists of a high-speed photovoltaic diode array and driver ci
GPIO_KeyInterrupt
- 按键进入GPIO中断服务函数，并采用延时函数来控制LED的亮灭。开发环境：TKStudio。使用中断函数需在vector_cfg.h中修改对应的中断，例如：#define PIOINT1_IRQ_Handle GPIOIsr0，还需要在vector_table.c中写外部函数定义，例如：extern void GPIOIsr0 (void) -Press the button to enter the GPIO interrupt service function, and use delay
c8051f040exampleforcan
- CAN1.c and CAN2.c are a simple example of configuring a CAN network to transmit and receive data on a CAN network, and how to move information to and from CAN RAM message objects. Each C8051F040-TB CAN node is configured to send a message wh
BTF040
- 6.压缩文件有密码 7.源码重复或已经存在 请不要上传有版权争议的内容和木马病毒代码和访问国外网站的代理软件 -/ CAN1.c and CAN2.c are a simple example of configuring a CAN network to // transmit and receive data on a CAN network, and how to move information to // and from CAN RAM message obj
led
- Simple LED Code. Toggles the DIP switches to turn LEDs on and off.
ej15
- sourcecode to use the timer0 witch will interrupt in 1 second and power on/off a led in P0.x with an lpc2103
pruebaledandboton
- power a led on and off by presing a button
LED_2443
- WinCE 2443 LED測試程式, 有4個LED, 開或關都會顯示-WinCE 2443 LED test program, it controls 4 LED that is attached on the ARM9 board, switch on and off are shown on screen
LED
- 8个LED分两组,分别实现轮流点亮,给视觉以闪烁感-8 led spit two item, turn on or turn off
pwm
- pwm控制led灯渐灭（C51单片机）通过对pwm的占空比和频率设置来控制led灯的变化-pwm control gradually led lights off (C51 MCU) on pwm duty cycle and frequency set to control the change led lamp
Electronic_stopwatch_features_plus_countdown
- 单片机做电子秒表。使用proteus仿真。设计要求：6位LED数码显示，计时单位为1/100秒。利用功能键进行启/停控制。其功能为：上电后计时器清0，当第一次（或奇数次）按下启/停键时开始计数。 当第二次（或偶数次）按下该键时停止计时，在一次按下启/停键时清0后重新开始计时。具有24秒减计数功能。 -SCM in the electronic stopwatch. Use proteus simulation. Design requirements: 6 LED digital dis
lsn8-9
- LED大屏灵星雨设置软件源程序，适合8、9版本，包含8、9版本可用的ledctrl.dll文件，已测试能通过DELPHI调用开、关屏，等操作，另外厂家还隐藏了几二十多个函数没说。-LED big-screen lsn to set software source code, for 8,9 version, contains 8,9 version available ledctrl.dll documents have been tested through DELPHI turn-on an
s3c2410wz
- 该资料是通过GSM模块控制S3C2410开发板的程序，使用短息控制板子上的三个LED灯的亮灭。-The information is controlled through the GSM module S3C2410 development board' s procedures, using the short rate control board on the bright three LED lights off.
LED
- 类型：驱动 功能：控制led灯的亮灭 1:表示点亮 0：表示熄灭-the led driver to control the led turn on or off
ctc_int
- Example of programming 82C54 timerswith 82C59 interrupt controller This example uses CTC channel 0 to monitor a tachometer type pulse input. The CTC is set to generate an interrupt for every 5 pulses which in the example equals 1 degree of rotation.
PCToMcu
- 基于凌阳单片机开发的案例 功能： 1.SPCE061A通过UART与PC通讯。 2. PC端可以用现成的串口工具，也可以自己编程实现PC端的串口收发。 3. 从PC上发送特定的数可以让SPCE061A控制发光二极管亮灭。 4. 可以实现在SPCE061A和PC间文件的传送。 5. 传输出错时有语音提示。 -Based on Sunplus Single Chip Case features: 1.SPCE061A through UART and PC communi
按键控制led
- 按键控制led灯亮灭顺序，从左到右跑或者从右往左跑(Press button to control the LED lights on and off)
LED
- LED跑马灯，多个LED灯轮流点亮熄灭,遍历后从头开始，不停止(LEDs are on or off in certain order)
LED control
- simple example on LabVIEW interfacing with Arduino Uno platform to control the ON/OFF status of the light on pin 13