搜索资源列表
SPI
- DSP SPI通信程序。把DSP的McBsp设置成SPI方式,对其内部的各内部寄存器进行配置,设置发送和接收中断。-DSP SPI communication program. The set of DSP McBsp SPI mode, the internal registers its internal configuration, set the transmit and receive interrupts.
McBSP_LOOKBACK_INT
- DSP 中关于如何将MCBSP配置为SPI的历程,很清晰,适合初学者 -Indispensable to learn DSP C language learning DSP C language indispensable data, you can compare the C language and C language in DSP in different places, so as to better grasp the DSP C language of DSP on how t
Voice-signal-acquisition
- 的I2C接口模块由串行数据SDA和串行时钟SCL组成语音信号输出时,可由DSP将语音数据通过McBSP接口发送给AIC23,再由AIC23的DA器件将他们变成模拟信号输出。-The I2C interface module by the serial data (SDA) and serial clock SCL composed voice signal output, the data can be sent through the voice DSP McBSP Interface to
66792264DEC6713_USB
- DSP利用MCBSP串口与USB通信源代码代码-DSP serial and USB communication MCBSP use source code
test_mcbsp1
- DM642的MCBSP通讯程序,可以实现DSP的MCBSP初始化、两片DSP的对接以及与其它具有MCBSP接口的设备进行数据交换。-MCBSP testing program,could realize the communication between DSPs through the MCBSP port.
MCBSP1_SPI
- dsp 5509a将多通道缓冲串口配置成spi方式。-Configure dsp5509a s mcbsp Port to spi mode。
better-and-longger-v0.1
- dsp2812常规实验和原理图:1.读写flash和sram 2.FM25CL64(spi)和24LC64(i2c) 3.SCI通讯;4.spi控制七段数码管;5.mcbsp控制ADS1274和TLV56066.DSP自带ADC;7.pwm1、pwm2和T1PWM波形输出 8 ecap 9 GPIO-dsp2812 general experiments and Schematic diagram
mcbsp_spi_loopback
- 本程序为DSP的mcbsp设置为SPI模式程序-This procedure for the DSP mcbsp set to SPI mode program
h7rs232
- 实现DSP串口通讯程序设计,掌握同步缓冲口McBSP的结构及工作原理(Implement DSP serial communication program design)
dsp28335工程
- 本工程为高压开关柜测量控制程序,能够控制断路器的分合闸动作,隔离的分合闸,旁隔的分合闸动作,能够测量断路器的分合闸线圈的动作电流,主回路的电压电流,检测断路器的分合闸的位置状态,能够检测高压开关柜的环境温湿度。 sciA的作用是有触摸屏通讯,波特率为115200.scia的接收中断接收8个字节,包括三个功能码,06功能码为设置数值,05功能码为控制。07功能码为自定义的,作用是告诉dsp发送给触摸屏电流值。 Scia发送中断可以发送四帧数据,第一帧为数字变量,发送一些位置变量。第二帧为模拟量