搜索资源列表
[DOS-Application]-Mix-Software---Power-C-2.00---D
- CA2832C. MOTOROLA RF DEVICE DATA. The RF Line. Wideband Linear Amplifier . . . designed for amplifier applications in 50 to 100 ohm
Timer0APWM_4F120
- 在PWM模式下使用Timer0A产生给定周期和占空比的方波。 Timer0A使用PF0或PB6。 使用PB6，是因为连接到开发板上的SW2。-Use Timer0A in PWM mode to generate a square wave of a given period and duty cycle. Timer0A can use PF0 or PB6. PB6 is used because PF0 is connected to SW2 on the Launchpad.
on-off-led
- LED blink..To build the circuit, attach a 220-ohm resistor to pin 13. Then attach the long leg of an LED (the positive leg, called the anode) to the resistor. Attach the short leg (the negative leg, called the cathode) to ground.
led-blinking
- To build the circuit, attach a 220-ohm resistor to pin 13. Then attach the long leg of an LED (the positive leg, called the anode) to the resistor. Attach the short leg (the negative leg, called the cathode) to ground.
12864
- 12864液晶的串行显示。将R9上的0欧姆的电阻去掉-12864 serial display. The 0-ohm resistor R9 to remove the
CC2520-CC2591EM-Reference-Design
- CC2520-CC2591EM 参考设计包含 CC2520-CC2591EMK 评估模块套件中使用的 CC2520-CC2591EM 评估模块的原理图和布局文件。 该参考设计演示了如何集成 CC2520 和 CC2591，并展示了用于去耦和射频布局的精湛技术。为了实现最佳射频性能，这些部件应当被精确复制。这是一个具有 SMA 天线连接器（便于射频输出与 50Ω 相匹配）和倒 F PCB 天线的 4 层参考设计。 -The CC2520-CC2591EM Reference Design
buck-and-a-full-bridge-converters
- It is a simulation project implementation of a buck converter connected to eighty ohm load which bucks or steps down the input voltage to obtain a lower voltage for the load. the second simulation is a full bridge converter which consists of two legs
m11b1-clusterpack
- A multimeter or a multitester, also known as a VOM (Volt-Ohm meter or Volt-Ohm-milliammeter ), is an electronic measuring instrument that combines several measurement functions in one unit. A typical multimeter would include basic features such as th
GpioLed
- 使用gpio引脚外接两个并联5欧姆电阻，一路电阻串接发光二极管 ，实现对发光二极管的控制-Gpio pin external use two parallel 5 ohm resistor in series resistance all the way to the light-emitting diodes, light-emitting diodes to achieve control
sibainxinggejiediandejisuan
- 利用BLT方程计算四边形环形网络，管道特性阻抗均为50欧姆，第五根线另一端接幅值为1V的电压源。可求解各个节点的电压响应与时域响应。-Use BLT equation quadrilateral ring network, pipelines are 50 ohm characteristic impedance, the other end of the fifth wires amplitude of the voltage source of 1V. Voltage response ca
7107
- 7107毫欧表 一种测量毫欧电阻的电路 -7107 Milliohmmeter a measure milli ohm resistor circuit
pin
- PIN photodiode. inputs x: optical signal fs: sampling frequency (Hz) Resp: receiver respsonsivity (A/W) R: receiver resistance (Ohm) T: temperature (degrees K) Id: dark current(A) output xrec: electrical signal
AD电压表
- 将滑动变阻器的值通过AD口将其ADC值转换为欧姆并显示在数码管上(The value of the sliding rheostat is converted to Ohm through the AD port and is displayed on the digital tube through the ADC port)
IRF4905
- IRF4905电压, Vds 最大:55V 开态电阻, Rds(on):0.02ohm 电压 @ Rds测量:-10V 电压, Vgs 最高:-4V 封装类型:TO-262 针脚数:3 频率, Pd:200W 封装类型:TO-262 封装类型, 替代:TO-262AB 晶体管类型:MOSFET 电压 Vgs @ Rds on 测量:10V 电压, Vds:55V 电压, Vds 典型值:55V 电流, Id 连续:74
M1_V01_Firmware20150116
- adc 采集电阻值，如果低于50欧姆，PWM驱动蜂鸣器发出声音(adc Res Value, if R less then 50 ohm ,pwm driver buzzer)
stm32与NB7W-TW00B通信
- 一个STM32芯片与欧姆人的NB7W-TW00B的MODBUS通信(hip; die; slug; wafer; CMOS chip ohm communication; communications; communicate; communicate by l)
LAB
- Charging circuit Assume that for the charging RC circuit above Vs = 10 volts and C = 10 microfarads. Plot the voltage across the capacitor if R equals 5k ohm, 10k ohms and 20k ohms. This just means that we are going to explore three time constants.(
danxiangqiaoshi
- 不控整流仿真 1.在MATLAB/Simulink中搭建单相桥式不控整流电路仿真模 型； 2.仿真分析空载的直流电压波形、交流电流波形； 3.仿真分析带载的直流电压波形、交流电流波形； 4.选择合适的滤波电感电容参数，观察分析其对直流电压的 抑制作用。（先完成2、3，再进行第4步） 仿真参数：交流电压有效值220V，频率50Hz，R=50Ω(Uncontrolled rectification simulation 1. build a simulation module of