搜索资源列表
232
- STC90C51单片机系统,采用C程序编程,该程序用于日RS485通讯,PC-从站.-STC90C51 SCM system using C programming, the program for the day RS485 communication, PC- slave.
ds18b20
- 基于stm32的4通道DS18B20温度采集板通过RS485总线发送采集数据给PC机。-Stm32 DS18B20 based 4-channel temperature data acquisition board via RS485 bus sent to the PC acquisition.
PPI
- S7-200plc PC RS485 vb6.0 ppi
PIC18f97J60TCPIP
- PIC18f97J60 EBoardConfig 上位机VC++源程序,用于测试上位机与以太网学习板进行RS485通信 EthernetBoard-V2.1 以太网开发板源程序 V4.51_Test-V2.1 TCPIP协议栈V4.51测试程序 Bootloader.hex Bootloader烧写文件,用于Bootloader实验-PIC18f97J60 BoardConfig PC C++ source code for testing PC with Ethe
VC485-serialcommpro
- 本例程演示了PC机和智能型仪表如何通过RS485接口进行通信。仪表采用专家自整定PID调节器,该仪表的通讯协议已经在例程代码中作了详细说明。-This routine demonstrates how PC and intelligent instruments through the RS485 interface to communicate. Instrument using the self-tuning PID regulator, the instrument of the comm
485
- rs485串口通信Proteus平台下仿真PC机到51单片机的RS485数据通讯,-Under rs485 serial communication to the PC simulation Proteus platform 51 single RS485 data communications,
stm32P485
- STM32+RS485串口通信,上位机是labview。-STM32+ RS485 serial communication, PC is labview.
tcpip
- 基于TCP/IP通讯的仪器仪表应用层协议架构由于新一代仪器仪表的数据量大,传输距离远,实时性高,传统的基于RS232/RS485的串行数据传送方式已不能满足要求,而基于TCP/IP的以太网数据通讯方式,传输距离大(通过internet,理论上无限远),速度快,是当前新一代仪器仪表数据传输的理想方式。 基于单片机(如MCS51+RTL8019AS)的以太网接入技术已经相当成熟,可以方便的与PC机连接。根据仪器仪表嵌入式应用的要求(如实时性),我们采用TCP协议或UDP协议进行数据传输。TCP是
XQUIKD
- modbus 源代码,RS485 通信,实现PC与RTU通信()
439245
- modbus 源代码,RS485 通信,实现PC与RTU通信()
MODBUS- 485SLAVER
- 本例程为 RS485 MODBUS 主站例程。可以通过按键发送相应的 MODBUS 命令,然后等待从站应答 (或超时)退出等待。 程序使用串口 3( USART1)与从机通讯,执行结果通过串口 1( USART1)送到计算机的串口。可以 通过 PC 机的串口终端软件观察程序执行结果(This routine is the RS485 MODBUS master station routine. You can send the corresponding MODBUS commands t
643122
- modbus 源代码,RS485 通信,实现PC与RTU通信()