搜索资源列表
IIC_TEST
- s3c6410 iic test program
s3c6410_leds
- 基于S3C6410的一个LED的驱动程序-S3C6410 an LED driver
adc
- FriendlyARM S3C6410 adc驱动-FriendlyARM S3C6410 adc driver
01led.tar
- s3c6410 开发板LED灯的裸板驱动-bare board driver s3c6410 development board LED lights
x210_usb
- 针对三星S3C6410的一个DRAM初始化程序。达内开发板使用,-Samsung S3C6410 the DRAM initialization procedure. Reached within a development board,
WIFI_Module_arm
- arm上面实现wifi应用源码,可以在S3C6410上面使用-arm to achieve the above the wifi application source code, you can use S3C6410 above
mms
- 家用保险舱温压控制系统的研究与实现针对家用保险舱的环境监控需求,设计了以S3C6410高性能ARM11处理器为主控制器,配置嵌入式Linux软件平台和Qt应用程序下的温压控制系统的研究和实现。重点介绍了传感器数据采集模块和监控中心软件的设计,实现了一个基于环境监控系统的温度和压强的实时数据采集和电子设备的自动控制的温压监控系统。-The the research of the for household insurance cabin control system of the temperat
GPRS
- 基于s3c6410控制SIM300进行短信收发 -Based on SIM300 s3c6410 control to send and receive messages
Camera
- 基于s3c6410控制摄像头采集图像,并存储为H264-S3c6410 control camera image acquisition and
key_button.tar
- s3c6410 按键驱动,不是根据输入子系统,完全按照字符设备驱动写的-s3c6410 按键驱动
in-out
- 在S3C6410开发板上,实现视频的采集,编、解码。编码使用的是h.264。-We capture the video and code&encode the video using the S3C6410.When we code the video,we chose h.264 format。
OK6410
- S3C6410裸机LCD液晶驱动程序,采用飞凌公司的OK6410开发板-S3C6410 bare metal the LCD driver, Fling OK6410 development board
setup-sdhci
- S3C6400/S3C6410 - Helper functions for settign up SDHCI devices HSMMC
13nand_flash
- linux下nand_flash裸板驱动代码,基于S3C6410开发板的,初学者可以参考一下~~不好的地方请指教-linux nand_flash bare board driver code, based on the S3C6410 development board, beginners can refer to a bad place please advise ~ ~
S3C6410
- 本文章主要讲述的是基于S3C6410C的嵌入式LINUX系统移植 很管用-This article mainly tells the embedded LINUX system based on S3C6410C transplant works
6410MDK_Project
- 这是s3c6410在MDK下的裸机程序(其中包含LED、LCD、定时器等一些代码),是学习arm11的入门资料,又给很多习惯了用MDK开发的同学带来很多方便。-This is s3c6410 under the MDK bare-metal procedures (including LED, LCD, timer and other code), is to learn arm11 introductory material, and for many accustomed to MDK de
21dm9000
- 基于s3c6410的dm900驱动 并实现ping arp等-Based on the dm900 driver s3c6410
u-boot
- 自己写的U-BOOT,目标板为S3C6410,能完成基本的硬件初始化,如GPIO、时钟频率、串口等,引导linux内核的地方有待改进,适合初学者研究,没有官方U-BOOT源码复杂,结构清晰简洁。-Write your own U-BOOT, target board S3C6410, able to complete basic hardware initialization, such as GPIO, clock frequency, serial, and guide linux kern
Aesop6410_Main_rev_2_0
- 一份很好的s3c6410原理图,有助于开发-A very good s3c6410 schematics, contribute to the development
spi-dev
- spi linux设备驱动,是s3c6410 arm11处理器需要的驱动-spi linux driver s3c6410 arm11 processor need