搜索资源列表
avr314
- 指南描述了一组用于SPI协议软件实现的低级程序,在主模式中所有的通信都来自AVR-guide describes a group SPI protocol software for the realization of the low-level procedures, the main mode of communication are all from the AVR
spra487c
- ti_dsp_6000系列,开发环境ccs3.1 文件内容,与spi_rom的连接,用串口实现spi协议-ti_dsp_6000 series, the development environment ccs3.1 contents of the documents, spi_rom connection with the use Serial Port spi agreement
SPI_verilogHDL
- 本原码是基于Verilog HDL语言编写的,实现了SPI接口设计,可以应用于FPGA,实现SPI协议的接口设计.在MAXII编译成功,用Modelsim SE 6仿真成功.-primitive code is based on Verilog HDL language, and achieving the SPI interface design, FPGA can be used to achieve agreement SPI interface design. MAXII success
SPI_Core.ZIP
- SPI协议的VHDL/Verilog语言实现。-SPI agreement VHDL / Verilog language.
SPI_FONCTION
- SPI 协议软件实现 用于nRF24L01射频IC与MCU的通讯 -SPI protocol software for the realization of nRF24L01 IC and RF communications MCU
contorl44
- 这是我毕设一部份,使用单片机进行控制,带i2c lcd 7279 和spi 协议-This is my part of a complete set up, use microprocessor control with i2c lcd 7279 agreement and spi
SPI 总线协议
- SPI 是一个环形总线结构,由ss(cs)、sck、sdi、sdo 构成,其时序其实很简单,主要是在sck 的控制下,两个双 向移位寄存器进行数据交换。 假设下面的8 位寄存器装的是待发送的数据10101010,上升沿发送、下降沿接收、高位先发送。 那么第一个上升沿来的时候数据将会是sdo=1;寄存器=0101010x。下降沿到来的时候,sdi 上的电平将所存到 寄存器中去,那么这时寄存器=0101010sdi,这样在8 个时钟脉冲以后,两个寄存器的内容互相交换一次。这样就完 成里一
mtk_spi_sd
- 在mtk平台上写的gpio口模拟spi协议的SD卡读卡器,包括对Mmc的支持
U-Reader
- cypress cy7c67300/cy7c67200 usb-host u-disc驱动代码,包括文件系统的解析和SPI协议的驱动,以及DMA控制。
AT45DBFlash
- 通过软件模拟SPI协议对存储器AT45DB进行读写函数
spi
- ARM程序,实现了SPI通信协议,可用于任何使用SPI通信协议的器件上,在LPC2103上测试成功。
adapter
- 用Verilog 实现将比特流数据转化为SPI协议数据的适配器
51模拟sd卡读写
- 51模拟sd卡spi协议的读写操作
AT25F512-1024
- AT25F512-1024.PDF软件工程师可以从本文件查到spi协议的的时序,从而开发出读写AT25F512-1024的程序
异步通信软件模拟,基于RS-232的串口通信,RS-485的多机通信,I2C总线协议的软件实现,SPI总线在单片机系统中的实现
- 2.1异步通信软件模拟2.2基于RS-232的串口通信2.3基于RS-485的多机通信2.4 I2C总线协议的软件实现2.5 SPI总线在单片机系统中的实现
spi_slave_test
- 实现spi协议的从机代码,亲测可用。按照字节接收,发送可以实现一次发送19字节,可按照需要更改。(The implementation of the code of the SPI slave protocol is available. By byte received, sending can be sent to send 19 bytes at a time, which can be changed as needed.)
STM32遥控器
- 该程序实现 adc对双轴传感器的X轴Y轴电压的采集,并用不同的标志位代表双轴传感器不同位置时的电压,利用SPI协议将采集到的数据传递给NRF24L01模块,利用NRF24L01模块将数据发送给下位机,实现与下位机之间的通信。(The program realizes the acquisition of the Y axis voltage of the X axis of the dual axis sensor by ADC, and uses the different symbol bi
NfcTest
- 使用RC522进行通信,采用SPI协议。目前只支持NTAG203芯片,其他芯片需要进一步改进通信的过程。(Use RC522 to communicate and adopt SPI protocol. At present, NTAG203 chips are only supported, and other chips need to further improve the communication process.)
spi_slave
- 使用VHDL语言写的程序,利用SPI协议实现串并转换电路(Programs written in VHDL language and series-to-parallel conversion circuit implemented by SPI protocol)
SPI_UVM_VIP
- SPI协议的芯片验证VIP,用UVM搭建平台验证代码(Chip verification VIP of SPI protocol, build platform verification code with UVM)