搜索资源列表
hf12864b2.rar
- ST7920 LCD 资料手册（引脚，时序，指令详细说明）,ST7920 LCD information manual (pin, timing, detailed instructions)
jfreechart-1.0.0-rc1.zip
- JfreeChart 常用图表例子，包括时序图、饼图、堆栈图、甘特图等,Examples of commonly used JfreeChart charts, including the timing chart, pie chart, stack map, such as Gantt Chart
clock.rar
- VHDL编写的，实现电子手表功能，硬件语言描写，定时非常准确,VHDL prepared, electronic watches, functions, hardware descr iption languages, timing is very accurate
ElectronicClock.rar
- 电子时钟设计汇编程序,用于微机接口实验平台，可以实现电子计时等功能。,Electronic assembler clock design, the experimental platform for the computer interface, you can achieve the functions of electronic timing.
mcp3421_example.rar
- 16位AD转换器mcp3421读写时序例程，在实际使用时，上电以后要软件复位一次，此例程经测试完全可以正常使用，已量产.,16-bit AD converter timing mcp3421 to read and write routines in actual use, to power after a software reset, the routine can be tested normal use, has been in volume production.
jiaotongdeng.rar
- 基于Proteus和Keil C 的交通灯控制，是学习MCS51（8951）单片机和液晶的优秀程序 程序功能：模拟交通灯控制系统 灯：南北方向：红3黄2绿3 东西方向：绿3黄2红3 黄色闪烁2次 键：紧急键，东西一个，南北一个，按下去后保持红色，直到松开键 要 求：定时要采用定时系统实现,Proteus, and Keil C based on the traffic l
ctimer
- 基于Windows MFC的高精度计时代码，方便需要精确计时的朋友。 CTimer-Using QueryPerformanceFrequency and QueryPerformanceCounter to perform high timing precision on windows platform.
wjnce-CAMERA
- 基于wince的底层驱动，用于生成dll的原始代码，本程序主要针对于sangsumg6410外围设备（camera）的驱动有严格的时序分析-Based on the underlying drivers wince, the original code used to generate the dll, the program aimed at sangsumg6410 peripherals (camera) driver has strict timing analysis
uartverilog
- verilog hdl FPGA vga时序显示经典源程序 很实用的-verilog hdl FPGA vga display timing source code very useful
counter-
- 用AT89S51单片机的T0、T1的定时计数器功能，来完成对输入的信号进行频率计数，计数的频率结果通过8位动态数码管显示出来。要求能够对0－250KHZ的信号频率进行准确计数，计数误差不超过±1HZ。-A single chip with AT89S51 T0, T1 timing counter function, to complete the input signal frequency counting, counting the frequency of 8 resulted in t
ipv6packet.rar
- 该代码实现了基于winpcap的IPv6发包功能，可以构造MLD,IPV6 UDP，IPV6 PIM类型的报文，实现了定时发送的功能,The code for IPv6 based on the contract winpcap functions, can be constructed MLD, IPV6 UDP, IPV6 PIM message types, to achieve the timing function to send
ultrasonic.rar
- 基于msp430f149的超声波测距.该程序允分利用430独特的定时功能很好的完成超声波测距功能.,Ultrasonic distance measurement based on msp430f149. The program themselves to sub-430' s unique timing function to use a good feature to complete ultrasonic ranging.
jishu
- 实现定时计数的功能的C语言代码，典型程序设计-Realize the function of timing count C language code, typical program design
51and-ds12887
- 51和ds12887组成的程序，我用这个程序改出了用2407控制ds12887的程序，说明他的控制时序是肯定好用的。-Composed of 51 and ds12887 program, I use this program to change out of control ds12887 procedures with 2407, indicating his control timing is certainly useful.
Gardneralgorithm
- 数字接收机中的Gardner定时同步算法-Digital receiver in the Gardner Timing Synchronization Algorithm
DS13B20
- 通过ds18b20的读写时序，测得室内的温度，而达到一种监控，附程序和实物图-Through reading and writing ds18b20 timing, the measured indoor temperature, and reached a monitor attached to the procedures and the physical map
FPGA
- 结合FPGA和以太网传输的特点，设计了一套数据采集系统，应用FPGA的内部逻辑实现对ADC、SDRAM、网卡控制芯片DM9000的时序控制，以FPGA作为采集系统的核心，通过ADC，将采集到的数据存储到SDRAM中，以FIFO方式从SDRAM中读出数据，并将数据结果通过以太网接口传输到计算机-Combination of FPGA and Ethernet features, designed a data acquisition system, application FPGA' s i
spi_V1.0.3
- //说 明：msp430通过模拟的spi驱动flash W25X32 //描 述：用于主函数中直接调用 flash写函数 写入数据 //功 能：写入flash 一个字节数据 flash地址自动加一 //端 口：p7.0 接/CS片选端 , p7.1用于时序脉冲, p7.2 用作MOSI主机输出从机输入 ， // p7.3用作MISO主机输入从机输出, // p1.4接/WP写保护引脚 ，此程序里没有用到 所以直接拉高，不用。 // 也可以连写 都试过了
RealtimeTest
- Ardence RTX 8.1环境下，采用.net开发的定时程序，并检测出定时精度。-Ardence RTX 8.1 environment, using. Net development of the regular procedures and detection of timing precision.
twice_freqencey
- 用Verilog直接完成倍频的算法,经过了quartus8.0的时序仿真-Verilog multiplier used directly to complete the algorithm, as a result of timing simulation quartus8.0