搜索资源列表
CAN总线与并口通讯转换
- 一个并口与CAN 总线转换的编程包括下位机与上位机的C与VC++程序,请大家参考- CAN CVC
sscom33串口通讯工具
- 这个是串口通讯工具,无论windows编程,还是嵌入式的上位机和下位机通讯,调试时使用它都很方便-This is a serial communications tools, windows programming, or embedded PC and the next crew communications, debug it very convenient to use
LaserScanning
- 89S51单片机通过PDIUSBD12的USB接口芯片实现与上位机通讯的固件源码,此包为一个二维激光光束扫描系统的单片机程序,包含USB固件,一个军事项目的部分工程-89S51 PDIUSBD12 microcontroller through the USB interface chip and PC communications firmware source, the package of a two-dimensional laser beam scanning system, the
dett
- 单片机程序,和上位机通讯,采集下位机的射频信号的功率,接收上位机的指令并向上位机回送采集到的下位机的信息,我花了一个月才开发出来的.绝对真实,可靠性强.-SCM procedures, and PC communication, collected under the crew of the RF signal power, PC to receive instructions to the PC to send collected under the crew information, I s
330
- 此程序为监测报警,用C51编,跟上位机通讯,用TINY小系统-procedure for monitoring the police, and C51 series, catch up with the crew communications, small system with TINY
DelphiStrSwitch
- Delphi字符进制转换源码,是单片机和上位机通讯的好工具-source base for the conversion of SCM and PC communication tool for
MCS51KAIFA
- 简易编程器软件含电脑上位机通讯软件及程器监控程序-simple programming software for PC computers with communication software and procedures for monitoring program
UARUSB
- 在USB/UART转换芯片支持下,通过USB接口使用UART与上位机通讯, // 当收到上位机发送的数据时,把接收到的数据发送到上位机,显示 // 在上位机串口调试软件上 // IDE环境: SUNPLUS u nSPTM IDE 2.0.0(or later) // PC机环境: 串口调试工具(PortExpert) // 涉及的库: CMacro1016.lib // 组成文件: main.asm // 硬件连接: USB线连接实验仪与PC的USB接口
uartdispy
- 户外显示屏源程序,含下位机源程序和上位机通讯程序(用delphi编写)-outdoor display source files, with the next crew and the source PC communication program (prepared with delphi)
can_bus_control
- 这个是机器人控制器的下位机程序,在8051下编译通过。可以与CAN总线上位机通讯,里面还包含了一些算法的实现。-the robot controller is the next crew, and in 8051 under compile. CAN Bus with PC communications, which also included some algorithm.
CANvb
- CAN上位机通讯程序vb与单片机通信时用的上位机程序
PCandMCU
- 我写的基于VB的单片机串口上位机通讯程序
mgt100
- 南瑞动控继电保护装置MGT100系列串口103规约上位机通讯程序 基于LINUX
D12_For_uCos-II
- UCOS实时系统中加入了usb d12驱动程序。可以实现和上位机通讯
mixed_machineGUI
- arm7最小系统的编程原码,具有与上位机通讯协议,能同时控制10个开关量与三个模拟量及三个脉冲量.
xjb
- 液晶显示,AD采集十六路数据,集中显示,可于上位机通讯
自由口通讯测试
- 和 S7 200自由口进行通讯,上位机采用VB控制.
msp430uart0
- msp430串口通讯程序,已字符串形式与上位机通讯
ODBCComm
- 单片机和上位机通讯用软件,用vc**编译,已经通过使用,完全正确
电子钟源程序
- 自行开发的51单片机电子钟程序,且带有上位机通讯的功能。-self-developed electronic bell 51 SCM procedures and communication with PC functions.