搜索资源列表
SerialCommunication1.18
- 打开串口通讯成功后, 实时监控区将显示实的温湿度值、 光照度值、经纬和温湿曲线。坐标范围可以手动输入,也可以使用默认值。 //通信协议 说明 包头 长度 设备类型 网络号 短地址 命令 数据 校验和 长度 2 2 2 2 2 1 1 位置 0 2 4 6 8
DHT11调试实验(亲测通过 串口显示数据)
- 温湿度传感器,sht11调试实验,串口显示数据。(Temperature and humidity sensor, SHT11 debugging experiment, serial port display data.)
串口通信+DMA接收不定长数据
- 串口通信+DMA接收不定长数数据,芯片是stmf103,平台是keil4(Serial communication +DMA receives the indefinite long data)
Router
- 能够支持串口RS232、RS485、以太网TCP/IP、UDP通信的数据采集程序,(Serial port and Ethernet data acquisition program)
STM8_模拟串口接收(接收单个字节完成)
- 利用STM8S103F3P6的普通IO口设计UART功能,波特率可以达到250Kbps,能够稳定的接收单字节数据并通过串口输出。模拟串口的发送也可以达到250Kbps.(Using STM8S103F3P6 general IO mouth design UART function, baud rate can reach 250 KBPS, can receive stable single-byte data and output via a serial port. Simulation
PortControlDemo
- C# winform 开发的串口通讯源码,实时监听COM口状态和数据传输。(C# WinForm development of the serial communication source, real-time monitor COM port state and data transmission.)
SerialPort.tar
- i.max283基于Qt5实现串口收发 最近将板子上的Qt版本升级到了Qt5,基于原生库实现了串口收发 1、对串口进行参数配置 2、打开了一个定时器,每3S发送一条命令 3、使用信号与槽机制,将收到的数据打印(qt serialport used for send and receive)
Hardware
- 根据环境数据进行网络转串口的可控继电器的控制(Control of a controlled relay with a network serial port based on environmental data)
Final20170823OK(micro)_Doing
- STM32 串口读取传感器数据并保存(STM32 serial port read sensor data and save)
serialPorts
- qt串口通信控制,收发、显示、数据位、停止位、流控、校验位、波特率(QT serial communication control, transceiver, display, data bit, stop bit, flow control, check bit, baud rate)
spcomm串口接收数据并以16进行显示出来
- spcomm串口接收数据并以16进行显示出来(The SPComm serial port receives the data and displays it with 16)
MYTOOLS
- C#开发的工业自动化控制类,大部分已经写完且验证过: 一、EPSON Robot Remote TCP/IP Control: 用于对EPSON机械手进行远程以太网控制; 二、Motion Control(GoogolTech/LeadShine):对固高和雷赛运动控制卡的DLL文件中的函数进行第二次封装; 三、Advantech: PCI1752:研华数据采集卡PCI1752更新输出及输出状态回读; PCI1754:研华数据采集卡PCI1754更新输入信号;
Serial_com
- 在linux qt 上用串口进行的数据发送接受通信,一个简单的实例,方便简易懂(Sending and receiving data by serial port on Linux QT, a simple example, easy to understand and easy to understand)
HMT_API_V4.XX
- 拓普微串口触摸屏底层驱动程序,包括51 单片机,和STM32的例程,程序包含画点画线,读数据、写数据,读按键等功能(Tuopu serial port touch screen driver, including 51 SCM, and STM32 routine, the program includes drawing dot line, read data, write data, read the keys and other functions)
ComSocket
- 本软件主要用vc++实现了串口通讯的调试,可以设置波特率等通讯参数,达到数据互通(The software mainly uses vc++ to debug serial communication, and can set the communication parameters such as baud rate and so on to achieve data exchange)
关于LabVIEW的一些程序
- 伺服电机控制 Modbus命令帧生成程序. 波形记录 数据的采集与显示 串口通讯 PID控制(Servo motor control. Modbus command frame generation program. Waveform recording. Data collection and display. Serial communication. PID control.)
9、CC2530 串口UART0发送字符串
- cc2530 uart模式 串口发送数据给cc2530 ,发送一次led闪烁一次(cc2530 uart send char.The led light when cc2530 received data from uart.)
Serial Read
- LabVIEW2014以上版本打开,一个简单的串口读取函数,通过串口从下位机读取数据,显示在上位机(A simple Serial Read Function which need LabVIEW 2014)
Com
- 在LabVIEW2016上编写的串口通信程序,可以实现收发数据,显示接收数据和波形。(The serial communication program written on LabVIEW2016 can receive and receive data and display the received data and waveform.)
Communication
- 实现无协议TCP通讯 、 数据接收事件 、连接成功事件。串口通讯,串口接收事件、(Implementation of non protocol TCP communication and data reception events)