搜索资源列表
lesson7
- 着重介绍单片机定时器/计数器使用方法和操作流程。-Highlights microcontroller timer/counter use and operational processes.
maibo
- 这是一个脉搏计数器单片机的程序,里面包含了一份报告,大家可以参考学习-This is a pulse counter microcontroller program, which includes a report, we can refer to learning
count
- 基于52单片机的数码管计数器c语言设计程序-Counter c language design procedures based on 52 single-chip digital tube
newjs
- 以51单片机为主控芯片,完成计数器系统。该系统能够实现:0-9999每秒加1的功能。-51 microcontroller as the master chip, the completion of the counter system. The system is able to achieve :0-9999 DPS 1 function.
Add-and-subtract-counter
- 用于单片机的加减计数器功能,可以完成按键的加减并在数码管上显示-For microcontroller-down counter, you can complete the addition and subtraction of the buttons and digital display
MIPS-2
- 51单片机的硬件实验:包括I/O控制实验、定时器计数器实验、按键与显示实验、并行AD、DA实验-51 microcontroller hardware experiment: I/O control experiments, the timer counter experiments, buttons and display experiment, parallel AD, DA experimental
stc51-Microcontroller-programe
- 压缩包中共有7个用keil编写的51单片机例程,分别可以实现:串口测温电脑显示、点阵流动广告模拟、多个18B20在1602液晶显示、红外解码1602液晶显示、双色点阵交替动态显示、能显示温度的万年历以及液晶显示的计数器。-Compressed package in a total of seven the 51 SCM routines with keil prepared, respectively, can be achieved: serial the thermometry comput
count
- 单片机使用计数器0和1并对计数器0和1进行方式1设定-Microcontroller counter 0 and 1 and counter 0 and 1 set
jishuqi
- 基于freescale HCS08 MC9S08AW60单片机的计数器显示模块-Based the freescale HCS08 MC9S08AW60 MCU counter display module
ds1302t
- 基于AT89S52单片机的多功能电子时钟系统,该系统可实现校时、闹钟、秒表、倒计时、计数器及温度测量等六种功能。-A multifunctional electronic clock system based on AT89S52 MCU which has six functions such as time correction, alarm clock, stopwatch, countdown, counter and temperature measurement.
0-9999count
- o--9999 计数器 同样是单片机控制 采用at89c51-o- 9999 counter is the same chip control using at89c51
serial
- c8051单片机串口通讯,将测量的温度与两个计数器的技术通过串口输出。-c8051 microcontroller serial communication, technology will measure the temperature of the two counter output through the serial port.
jishu
- 利用单片机,模拟工厂里的产品扫描计数器。用按键代替扫描开关,可实现计数和清零等操作。-Use of microcontroller, analog factory scan counter. Switch button instead of scanning operations such as counting and cleared.
counter
- 单片机应用下的计数器程序,可以用于电机转速(高、低速度)、频率(高、低频率)测量-Counter program, under the SCM application can be used for motor speed (high and low speed), frequency (high and low frequency) measurements
1
- 用外部中断输入引脚RB0/INT接收连接在该引脚上的按键信息。每检测到一次按键就对8位计数器COUNT 加1,将COUNT的值直接送给8个发光二极管显示。 单片机复位后,COUNT的初始值为二进制数00000000B,对应的8只发光二极管都不亮。当按键RB0/INT被按下时,COUNT的值加1,发光二极管D0点亮,以表示二进制数00000001B。然后松开按键之后,如果再次按下RB0/INT时,COUNT的值加1,发光二极管D1点亮,以表示二进制数00000010B……,以此类推。通过观测
my-work
- 基于单片机yye_mini51开发板的测试程序 流水灯 按键扫描数码管显示 计数器 动态数码管 矩形键盘 等 等 -the yye_mini51 development board test program light water key scan digital display counter dynamic digital tube rectangular keyboard
dzwnj
- 基于51单片机定时/计数器的详细电子万年历程序-Based on 51 single-chip timer/counter electronic calendar program. .
danpianjijishuqi
- 51单片机实现的计数器功能,已经测试可以正常运行。-51 MCU counter function has been tested can operate normally.
cfm_count
- 程序可以完成以下功能: (1)本程序以stc12c5410ad为控制器而设计 (2)本程序可以完成计数功能,最大值为9999。 (3)计数接口采用stc12c5410ad的第13个引脚,即P2.5。 (4)P2.5平时为高电平,当P2.5变为低电平,且低电平时间超过907us时,则计数器加1。 (5)本程序具有计时功能,当单片机上电复位之后开始计时,时间以秒的形式显示出来。 计时最大值为9999s。 (6)四个数码管显示计数值,当按下KEY3键时,显示时间,即单片机
MCU
- AT89C52单片机整体介绍,包含指令系统,汇编语言程序设计,中断,定时器计数器,串并扩展和人机交互-AT89C52 microcontroller overall, including instruction, assembly language programming, interrupt, timer counter, serial-to-parallel extension and human-computer interaction