搜索资源列表
nonlin
- 有限元非线性分析源程序，用FORTRAN90编写，主要用于非线性有限元分析-nonlinear finite element analysis of the source, with FORTRAN90 preparation, mainly for nonlinear finite element analysis
PCELM1
- 国外有限元分析源程序1，用FORTRAN编写，用于结构的有限元分析。-abroad finite element analysis a source with FORTRAN prepared for the structure of the finite element analysis.
PCELM2
- 国外有限元分析源程序1，用FORTRAN编写，用于结构的有限元分析。-abroad finite element analysis a source with FORTRAN prepared for the structure of the finite element analysis.
PCELM3
- 国外有限元分析源程序2，用FORTRAN编写，用于结构的有限元分析。-abroad Finite Element Analysis source 2, FORTRAN prepared for the structure of the finite element analysis.
PCELM4
- 国外有限元分析源程序4，用FORTRAN编写，用于结构的有限元分析。-foreign source Finite Element Analysis 4, FORTRAN prepared for the structure of the finite element analysis.
PCELM5
- 国外有限元分析源程序5，用FORTRAN编写，用于结构的有限元分析。-foreign source Finite Element Analysis 5, FORTRAN prepared for the structure of the finite element analysis.
PCELM6
- 国外有限元分析源程序6，用FORTRAN编写，用于结构的有限元分析。-foreign source Finite Element Analysis 6, FORTRAN prepared for the structure of the finite element analysis.
woli1
- 这是基于Pro/Engineer Wildfire的有限元分析程序-This is based on Pro / Engineer Wildfire finite element analysis program
jCAE-src-0.5.tar
- 有限元分析软件，造型部分采用opencascade造型内核实现，界面显示采用Java/Java3D ,通过Corba调用opencascade函数进行造型与有限元分析。- Finite element analysis software, the modelling partially uses the opencascade modelling essence realization, the contact surface demonstrated uses Java/Java3D, t
FEX
- 用java做的平面珩架结构有限元分析软件。 基本性能如下：结点数<500,单元数<1000，（具体情况视内存大小而定）在一般的微机 上，算一百节点以下的结构，基本上不用等待。-do with the plane Heng Structure finite element analysis software. The basic properties as follows : nodes lt; 500, Number of units lt; 1000, (depending
NURBSCS
- NURBSCS曲线曲面造型，进行CAE有限元分析，-NURBSCS surface modeling, finite element analysis CAE,
matlabyouxianyuan
- 本文讲述了matlab在有限元分析中的应用，为kdh文件，用cajview打开-This paper describes the Matlab in finite element analysis applications. For documents, with open cajview
SpMatrix
- 针对有限元分析的稀疏矩阵采用一维存储时的矩阵运算编写的，可对其进行加减乘除和LU分解等运算-against the finite element analysis using a sparse matrix storage dimensional matrix prepared by the operator, can its arithmetic and LU decomposition, etc. Operational
zhouchengzuo
- 有限元分析设计轴承软件，一般采用ANSYS去进行分析应力等作用-finite element analysis software design bearings, normally used to ANSYS stress analysis, etc.
FEM_gauss
- 有限元分析作业源码, piecewise单元,积分 高斯近似算法两种，并计算最小势能-Finite Element Analysis Operating source, piecewise unit, integral Gaussian approximation algorithm for two, and calculation of minimum potential energy
ThefiniteelementmethodusingMatlab
- 《The finite element method using Matlab》源程序及电子书 用Matlab进行有限元分析-"The finite element method using Matlab" source procedures and e-books using Matlab for Finite Element Analysis
cavity2_map
- 很强的有限元分析软件ansys55的源码，用于计算规则长方体空腔的固有频率和模态-strong finite element analysis software ansys55 source code, rules for the calculation of the rectangular cavity natural frequencies and mode
有限元作业
- matlab作力学分析实例，并于ABAQUS对照。(The example of mechanical analysis is made by MATLAB and compared with ABAQUS.)
一个斜拉桥的计算空例
- 一个ANSYS APDL命令的斜拉桥模型，可进行静力分析，模态分析(A cable-stayed bridge model with ANSYS APDL command can be used for static analysis and modal analysis)
线弹性动力学FEM分析
- 采用有限元计算，可以仿真二维、三维线弹性动力学问题(matlab code for the simulation of linear elastic dynamic problems by using FEM)