搜索资源列表
C8051F500
- 12864显示,控制颜色采集,温度探测,加热,电机,齿轮运动-12864 display, control the color acquisition, temperature probe, heating, electrical, sports gear
lead_free_soldering_station
- 用AVR单片机实现的某品牌恒温无铅焊台的程序;原理就是定时检测温度,低于设定温度时启动加热。-AVR Microcontroller with a certain brand of lead-free soldering station temperature process principle is to regularly test the temperature, lower than the set temperature starts heating.
temperature-control
- 1)、有自动的温度检测功能,能用数码管显示温度。 2)、当锅炉温度超过上下限值时出现相应报警或亮灯。(当温度超过上限值则自动停止加热:当温度小于下限值则自动开始加热。) 2、自动水位监控系统: 1)、有自动的水位监控功能。 2)、锅炉水位超过上下限值时出现相应报警(蜂鸣器发出两种不同的声音)。 3)、当水位超过上限值则自动响铃并停止进水(关水泵)。 4)、当水位小于下限值则自动响铃并启动加水装置(开水泵)。 -1), with automatic temperatur
temperature-controller
- 利用实验设备上8255扩展LED显示电路,A/D转换电路,完成类似恒温控制实验。其中利用数码管显示设定温度,利用可变电位器模仿温度变化,用ADC0809采样可变电位器的输出电压作为采样温度,将ADC0809采样到的温度以十六进制形式显示在屏幕上,并且与设定温度做比较,当采样温度超过设定温度时,启动制冷电机即亮红灯;当采样温度低于设定温度时,启动加热电机即亮绿灯。分别利用红、绿两只发光二极管发光表示制冷、加热电机工作。当采样温度等于设定温度时,红绿灯都不亮-8255 using experimen
Temperature-control-program
- 温度控制 有DS18B20记录温度 如果温度超过会报警 如果温度过低 会自动加热-DS18B20 temperature control and record the temperature if the temperature exceeds the alarm if the temperature is too low will be automatically heated
EMPER
- 本系统的设计可以用于热水器温度控制系统和饮水机等各种电器电路中。它以单片机AT89S52为核心,通过3个数码管显示温度和4个按键实现人机对话,使用单总线温度转换芯片DS18B20实时采集温度并通过数码管显示,并提供各种运行指示灯用来指示系统现在所处状态,如:温度设置、加热、停止加热等,整个系统通过四个按键来设置加热温度和控制运行模式。-This system can be used in the design of the water heater temperature control sys
measurement-and-control
- 课题设计:二极管测温并控制烘箱温度 要求:能实现对加热器温度的测量、自动控制加热、手工调节控制温度。 要对方案的性能、成本、体积、难易程度等进行分析与比较,本着以满足功能要求为前提,不要一味提高性能指标,并且要考虑可能涉及到的原材料的货源是否困难等,综合考虑,确定方案。 xu__chuanghua 淮安信息-Study design: diode temperature measurement and control the oven temperature Requiremen
virtual
- 基于51单片机的模拟空调温度控制系统,白炽灯加热,12V直流无刷风扇用来制冷-51 MCU-based simulation air temperature control system, heated incandescent, 12V brushless DC fan for cooling
reshuiqi
- 热水器可以对其温度进行设定 当到达一定温度后进行自动加热,数码管显示-Water heater can be set when its temperature reaches a certain temperature for automatic heating, digital display
heater
- 电磁炉程序:利用PWM实现温度的控制,利用温度传感器检测加热丝的温度并实现恒温的控制。-Induction procedure: using the PWM to achieve temperature control by using a temperature sensor detects the temperature of the heating wire and to achieve constant temperature control.
ProcessControl
- 化工上的程序控制 系统:二阶串联回馈热搅拌器,使用2个热交换器分别对2个串联的搅拌槽加热。 控制策略:我们将利用2个控制阀来控制热交换器,以维持T2和T4的温度在理想的控制范围之内 可计算:GP,GV,GC,误差值时,PID 可做动态测试 附上文件操作及说明档-Chemical process control on System: Second-order hot mixer series feedback, the use of tw
12864P18B20P24C02
- 18B20读取水温度,按键设置水温界限,可以智能加热和保温。-18B20 read water temperature, set temperature limits of keys can be intelligent heating and insulation.
wenkong-last
- 采用STC90C516RD+单片机芯片控制最小系统,从DS18B20防水温度探头测量温度,并显示1602液晶上。温度控制由单片机内部定时器控制继电器开关来加热并计时。时间显示利用时钟芯片1302设置和读取日期时间同时显示在液晶显示屏上。-failed to translate
20111016
- 空调控制装置的电路设计据半导体制冷器(TEC)和PTC 的物理特性分析了空调控制装置的技术关键,在分析温度控制的特点,以及在当前国内外在温度控制上所采用的方法的基础上,针对半导体制冷和PTC加热的原理设计出半导体制冷器和PTC加热的驱动电路,其具有控制精度高、控制温度范围大、制冷响应速度快等优点。-Air conditioning control device according to the circuit design of thermoelectric devices (TEC) and
stc12c5a60s2Pds18b20Plcd1602_PID
- 实现功能:根据测量温度,进行PID控制加热,PWM输出。 实现单片机:stc12c5a60s2-Functions: to measure temperature, the heating of PID control, the PWM output
Temperature-control
- 温度控制/本实验程序为温度控制实验,实验内容为通过A/D转换器从温控模块获取温度信息,在Nios控制器中对温度信息,进行处理,同给定的目标温度值比较,然后发出继续加热或者停止加热的信息,从而 实现闭环控制。-Temperature control/this experiment procedure for temperature control experiment, experiment content for through the A/D converter for temperatu
Pid-temperature
- plc程序设计,给加热器设定一个温度给定值,经过一段时间的加热,要求加热器温度基本可以稳定在该值上-PLC program design, to the heater set a given value temperature, after a period of heating, heater temperature basic requirements can be stable in the value
Incubator
- 使用的单片机为stc12c5628ad,控制温度为0-60度,设定温度低于室温时,通过开停压缩机控制箱内温度;设定温度高于室温时,通过pid算法控制加热管来控制箱内温度-Microcontroller for use stc12c5628ad control the temperature of 0-60 Degrees Celsius, when seting the temperature lower than room temperature,it will stop the compre
tempe_pid
- 基于PID算法的温度控制系统 89C51单片机,通过键盘输入预设值,与DS18B20测得的实际值做比较,然后驱动制冷或加热电路。用keil C语言来实现PID的控制。 -Temperature control system based on PID algorithm 89C51 microcontroller, through keyboard input default value compared with the the DS18B20 measured actual va
BS18b20
- 基于51单片机 用DS18B20检测温度并数码管显示 当前温度超出设定范围 则报警 并采取加热或制冷来调节温度-Based on single chip DS18B20 detection with 51 temperature and digital tube display the current temperature exceeds the scope is set to take the heat or refrigeration to adjust temperature