搜索资源列表
DHT11_TSET
- 很好的51单片机温湿度传感器DHT11程序代码,采用串口打印温湿度传感器DHT11的返回值。大家可以拿来参考。-Very good 51 single-chip temperature and humidity sensor DHT11 program code, using serial port temperature and humidity sensor DHT11 return value. We can bring a reference.
STM32-DHT11
- STM32 DHT11温湿度传感器的代码,使用模块化编程使代码看起来很清晰。解析过程简单明了。-STM32 key timer in the use of the state machine, not applicable delay, high efficiency.
stm32-DHT11
- stm32 操纵DHT11温湿度传感器获取数据-Stm32 manipulates DHT11 temperature and humidity sensor to obtain data
51_DHT11
- 温湿度传感器DHT11的驱动程序 微处理器平台为宏晶公司的STC15W4K56S4。已经测试成功。-Temperature and humidity sensor DHT11 driver, microprocessor platform for Acer crystal company s STC15W4K56S4. Have been tested successfully.
文档3
- dht11温湿度传感器测量温湿度的完整程序,希望能帮助你(PHT11I hope this file can help you in some way)
9.DHT11温湿度检测(测试通过)
- 基于STM32F103C8T6的温湿度传感器代码,已调测通过(STM32F103C8T6 based temperature and humidity sensor code, has been measured through)
HumiTemp-DHT11
- stm32采集温湿度DHT11传感器数据(Stm32 collects temperature and humidity DHT11 sensor data)
DHT11 FOR IOT
- 用在树莓派的Windows 10 IoT系统的控制温湿度传感器的程序, 主体用C#写的,DHT11的驱动引用了一个C++文件。(A program for controlling temperature and humidity sensors used in raspberry pie Windows 10 IoT systems. The main body is written in C#, and the DHT11 driver refers to a C++ file.)
dht12
- DHT12温湿度传感器采集程序,单总线方式(DHT12 temperature and humidity sensor acquisition procedures, single bus mode)
温湿度传感器
- STM32 1系列用DHT11模块显示湿度 在OLED屏幕上显示的程序(The STM32 1 series displays the humidity displayed on the OLED screen using the DHT11 module)
test
- dht11温湿度传感器驱动程序,并且显示在lcd上,亲测可用((dht11 temperature and humidity sensor driver, and display on lcd, pro-test available))
DHT11
- 单片机读取DHT11传感器的温湿度数据,(Reading temperature and humidity data by single chip microcomputer)
嵌入式作业
- 通过DHT11采集温湿度,通过显示屏打印,通过nrf24l01发送给上位机。(Collect temperature and humidity through DHT11, print through the display screen, send to the upper computer through nRF24L01.)
DHT11调试实验(亲测通过 串口显示数据)
- 温湿度传感器,sht11调试实验,串口显示数据。(Temperature and humidity sensor, SHT11 debugging experiment, serial port display data.)
基于ARM的智能家居远程监控
- 基于ARM的智能家居远程监控:控制主机STM32F103VET6、无线短信收发模块GPRS(远程监控的主要模块)、用于显示的LCD1602液晶显示屏(显示测量出来的温湿度值)、测量外部环境温湿度的温湿度传感器DHT11,异步电机28BYJ-48(模拟控制窗帘收放用到的控制器)、蜂鸣器(报警用)、LED灯(模拟室内各种灯)、继电器(模拟室内各种电器的控制开关)。(Remote monitoring based on ARM Home Furnishing intelligent control c
DHT11
- 基于STM32的DTH11温湿度传感器的驱动程序(STM32-based DTH11 temperature and humidity sensor driver)
孵化环境温度监控
- 如果要将此应用项目移植到开发板上,只需要根据此项目的电路图修改管脚,改成我们开发板对应的管脚上。温湿度传感器使用的是DHT11,所以数据口按照原理图内接。温度传感器接口也需要修改成我们开发板对应的接口(If we want to transplant this application project to the development board, we only need to modify the pins according to the circuit diagram of this
STM32使用I2C驱动GY-30光照传感器和SPI总线驱动DHT11
- 对于光照传感器的使用,在串口调试助手上将光照强度显示出来,每隔2S,读取一次,否则会出现读取失败。 对于温湿度传感器也是同样的道理,只是为了节省GPIO口,使用SPI单总线通信模式,实现对于温湿度的数据采集以及显示。 其中还包括了对应的串口通信,以及对于printf的重定向,使其打印在串口助手的接收区。
STM32_DHT11_OLED
- 基于STM32F103C8T6单片机的环境检测系统,应用DHT11温湿度传感器,MQ135烟雾传感器,检测环境温湿度,烟雾,可燃气,检测到烟雾蜂鸣器报警,将实时数据显示在OLED屏上,且有按键可以修改报警值。(Based on STM32F103C8T6 microcontroller environment detection system, DHT11 temperature and humidity sensor and MQ135 smoke sensor are used to det
16DHT11
- 在stm32f407上实现dht11温湿度传感器(DHT11 temperature and humidity sensor based on stm32f407)