搜索资源列表
Experiment01
- Fpga入门实验一：点亮led灯。verilog语法-Fpga entry Experiment 1: light led lights. verilog syntax
Lab0301-LED
- dsp实验中LED灯的闪烁，程序运行之后可以看到四个灯被一次点亮-dsp experiment flashing LED lights, you can see after running four lights are lit again
led
- 一个led灯的花样控制程序，实现16个灯的花样点亮和熄灭，供初学者下载-A led light pattern control procedures, to achieve 16 light patterns light up and off, for beginners download
led-on
- 是一个单片机点亮一个LED 灯的实验 简单通俗易懂 很适合刚开始学单片机的人用-led on
C
- 51数码管片选实现例程，点亮LED灯显示相关数据-failed to translate
myled
- linux下的LED驱动，在TQ2440开发板上实现按键点亮LED的功能。-The Linux LED drive, in TQ2440 development board realize the function of the key light LED.
mini2440_led
- 项目实现了mini2440上led点亮，主要包括ARM启动代码以及led的驱动代码-The project has achieved led lighting on mini2440, including ARM startup code, and the driver code of led
ganggaopai
- 使用8051点亮LED灯的广告牌程序，有源码和仿真，为本人大学所做项目，经过测试很稳定-Use 8051 lit LED lamp of the billboard procedure, have the source code and the simulation, the university for my project, after testing is very stable
32LEDAVR
- 控制AVR的32个IO口点亮LED花样交替流水显示。-Control the AVR IO port 32 LED light water show alternating pattern.
led_test1
- 实现简单的在FPGA上点亮led灯实验，已经在xilinx的V2p板子上跑通过，对初学者可能会有用-The experimental realization of a simple light led lights on the FPGA, xilinx V2p board to run through, may be useful for beginners
led
- 动态的霓虹灯 在同一时间内8个LED循环点亮并闪烁，使用一个8×8点阵LED显示“生命在于运动”，-led
test
- led灯的控制以及开通与关断等等，用来点亮led灯-control, and the opening of the led lights and the turn-off to light the led lights
ledwater
- 跑马灯实验：利用计数器轮流点亮LED灯，实现各种动态效果。-Marquee experiment: the use of the counter in turn lights up the LED lights, a variety of dynamic effects.
2-key-recognition-and-LED-indicator
- 硬件环境： 按键：Key1--PD2 Key2--PD3 （低电平表示有按键按下） LED：LED1~LED8--PC0~PC7； （LED在高电平被点亮） 功能：当Key1按下时，所有8个LED的均被点亮 当Key2按下时，所有8个LED均被熄灭-Hardware environment: Key: Key1-PD2 Key2-PD3 (low level said keys pressed) LED: LED1 ~ LED8-PC0 ~ PC7 (L
DEMO_V
- fpga点亮led灯的小程序 适合初学者-fpga led
armand51tongxin
- 51单片机发送，三星的S3C2440接收，并点亮led小灯，通信波特率是115200，单片机采用定时器2来实现该波特率-51 SCM to send, samsung s S3C2440 receiving, and lit led lights, communication baud rate is 115200, microcontroller timer to achieve this by 2 baud rate
led
- 博创S3C2410点亮3盏LED灯的汇编代码-The ASM Code of the base experience using UP-TECH S3C2410 to light 3 leds.
LED
- 10个LED全部点亮，稍后全部熄灭，此过程中用于检测LED是否有损坏 8位数码管全部显示“8.”，稍后全部熄灭，然后显示“0 ~ 7”，用于测试数码管有无缺段。-All 10 LED lights, all out later, this process is used to detect LED is damaged 8 digital tube show all "8", later all off, and then display 0 to 7 for testing digit
led
- 本实验完成发光二极管的循环点亮实验，由于输入晶振为20M，分频得到count1信号，故每间隔约1S彩灯循环移位一次。 也可以外接32768hz的晶振经4060分频后的1HZclk输入，自己可以尝试改变实验，加以练习。-In this experiment completed the cycle of light-emitting diode light experiments, as a result of the importation of crystal for the 20M, sub-
leds
- 点亮led灯的c语言程序，在s3c2440上运行，编译就行了-C language program, in light led lights s3c2440 on run, compile and