搜索资源列表
spi
- spi总线配置，protues模拟spi总线点亮LED，-spi bus configuration, protues simulation spi bus lit LED
SIM300---duanxin
- 通过SIM300的通信，发短信来点亮LED灯。程序很完整，测试过没问题。-Through the SIM300 communication, send text messages to light up the LED lights. The program is very complete, tested no problem.
led
- 这是一个基于FPGA的数码管点亮程序，从0到F循环点亮。-This is a based on FPGA digital tube light program, from 0 to F light cycle.
STM32-
- STM32 点亮LED 北京泛海建设的后防悍将-STM32 lit LED Beijing Asia Standard construction of defensive midfielder
stm32led
- stm32f103vbt6单片机点亮led-the code on stm32 to light a led
led
- 用ATMEGA 128 芯片开发板点亮流水灯-ATMEGA 128 chip development board lit water lights
HZK16
- 汉字字符编码文档，做LED显示时，使用它可以吧汉字转化为对应二进制来点亮led亮点显示使用-Chinese character coding documents do binary display use
exp3
- 花样流水灯：8个发光二极管D1~D8分别接在单片机P0.0-P0.7端口上，一个开关接在P3.0上。要求输出端口输出“0”时，发光二极管亮。开关闭合时，开始按P0.0+P0.7、P0.1+P0.6、P0.2+P0.5、P0.3+P0.4的顺序依次点亮LED，再按P0.3+P0.4、P0.2+P0.5、P0.1+P0.6、P0.0+P0.7的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。-Mood Light water: 8 LEDs D1 ~ D8, respectively, c
led
- arm板上led灯的驱动程序开发，点亮或熄灭-arm board led lamp driver development
liushuideng
- 多种方式点亮LED灯，依次循环，可控制改变方式-A variety of ways to turn on the LED lights, turn cycle control to change the way
TQ2440
- 基于天嵌TQ2440开发版的裸机代码源码包括点亮LED让LED闪烁还有按键程序（利用断或查询的方式），串口的源代码，可直接烧进开发板运行-The day embedded TQ2440 Developer Edition bare metal code source-based lit LED LED flashes also key program (off or query), the serial port of the source code, can be directly burne
GPIO_LED
- 基于NRF24LE1点亮LED灯程序，它是NRF24L01的升级版-Based NRF24LE1 lit LED lights, which is an upgraded version of NRF24L01
danpianj_led
- 单片机初学者程序之一，led灯，最基础的单片机程序 点亮led-danpianji chuxuezhe led deng zuijichu de danpianji chengxu
light
- verilog light 使用DE2_70开发板实现点亮LED,verilog HDL语言编写-verilog light DE2_70 LED verilog HDL
scanled
- 利用FPGA系统电路控制8个LED进行4种工作模式状态的循环显示,这四种工作模式状态是：（1）从左到右逐个点亮LED（2）从右到左逐个点亮LED（3）从两边到中间逐个显示LED（4）从中间到两边逐个显示LED.-The FPGA system circuit control 8 LED status of the four operating modes cycle through four operating modes state: (1) from left to right by-lit
linux-module
- Linux设备驱动标准模板,用于s3c2410实验,流水灯点亮,下面有配套应用程序内核版本：2.6.31 交叉编译器：arm-linux-gcc 4.12 Read,write,ioctl等函数实现 S3C2410 GPF0~GPF3外接led灯,低电平点亮,高电平熄灭分别用write和ioctl 实现led流水灯的点亮经过验证,可点亮led流水灯-linux module
LED
- LED灯流水显示，形成跑马灯的形式，从左到右依次点亮，至一排全部显示，再熄灭，如此重复-LED light water show, the formation of the form of the Marquee, lit from left to right, to a row of Show All, and then goes off, so repeat
LED_C
- S3C2440A平台，ADS 开发环境调试环境，写ARM的C语言编程，点亮LED灯。-S3C2440A platform, ADS development environment debugging environment, wrote ARM C programming language, light LED lamp.
Main
- s3c2440裸机程序开发：用轮询方式实现按键点亮led。-s3c2440 bare metal program development: polling mode button is lit led.
LED
- 该源码可以使一个16*16的LED显示屏显示动态图片，可以使文字上下左右移动。也可以使用光笔点亮、擦除、拖动LED上的点。也可以使用光笔写的字上下左右移动。-The source code can make a 16* 16 LED display shows the dynamic picture can make the text up and down and move around. You can also use the light pen lights, erase, drag t