搜索资源列表
LED
- 点亮一个LED灯,本程序是通过C语言编程的，属于比较简单-Light a LED light, the C programming language, are relatively simple
51dog
- 51内核单片机看门狗测试程序，点亮LED，测试单片机89C52-51 core microcontroller watchdog test procedures lit LED test 89C52 microcontroller
led_decoder
- 这个是用verilog语言写的一个点亮LED灯的程序，在DE2最小系统板里验证过-This is to use verilog language written by a light LED lights program, in DE2 minimum system board validated
Zigbee-KEY
- 相信大家经过例程1点亮LED实验后对CC2530的编程以及IAR的编译方法有一定的了解。我们来讲解一下zigbee模块的按键实验，按键是实现人机交互必不可少的东西，我们实验就用来实现按键控制LED。-I believe that after routine lit LED experiment the CC2530 programming and IAR compiler method. Explain zigbee module key experimental, the key is to
LM3S_uCOS2_IAR_Led
- 嵌入式系统实验点亮LED，适合初学者进行研究和分析研究。-Experimental lit LED embedded systems
LED
- LED点阵书写屏系统，在控制器的管理下，LED点阵模块显示屏工作在点亮模式下；当光笔触及LED点阵模块表面时，先由光笔检测触及位置处LED点的扫描微亮以获取其行列坐标，再依据功能需求决定该坐标处的LED是否点亮至人眼可见的显示状态-LED dot matrix screen writing system in the control of the management, display LED dot matrix module lighting mode When light strokes
456
- 点亮led灯，通过单片机控制led灯的亮灭，程序觉对可用，简单-SCM control lighting led lights led lamp light off, procedures sleep on the available
LED
- 该程序是dspic30f4011的源代码，适合刚上手的学员，一个简单的LED点亮，对入门会有很大的帮助-The program is dspic30f4011 source code, suitable for students just to get started, a simple LED lights, there will be a great help to the entry
KEY_LED
- 一个入门级的程序，按键点亮led的程序！初学可以下载下来参考~-light led
K1-K4-packet-control-LED
- 每次按下 K1 时递增点亮一只LED，全亮时再次按下则再次循环开始， K2按下后点亮上面4 只LED，K3 按下后点亮下面4 只LED，K4 按下后关闭所有LED-Each press K1 increments lit a LED full brightness when pressed again, the cycle begins again after 4 LED lit above press K2, K3 Press lit following four LED K4 Press
K1-K4-packet-control-LED
- 每次按下 K1 时递增点亮一只 LED，全亮时再次按下则再次循环开始， K2 按下后点亮上面 4 只 LED，K3 按下后点亮下面 4 只 LED，K4 按下后关闭所有 LED -Each press K1 increments lit a LED full brightness when pressed again, the cycle begins again after 4 LED lit above press K2, K3 Press lit following four LE
LED.RAR
- 单片机程序，点亮一个LED灯的小程序， 相当于HELLO WORLD，让你有一个惊喜-Microcontroller program, a small program to light up an LED light, equivalent to HELLO WORLD, let you have a pleasant surprise
led
- 按下数字键显示器的个位显示相应的数字 功能键F1：点亮P0.4口上的发光二极管 功能键F2：熄灭P0.4口上的发光二极管 功能键F3：点亮P0.5口上的发光二极管 功能键F4：熄灭P0.5口上的发光二极管 *键：显示器显示字符“ABCD” #键：同时点亮P0.4\P0.5口上的发光二极管 -Press the number keys display units display corresponding the digital function keys F1: li
Numb-LED
- 基于51单片机的LED数码管动态显示，LED数码管动态显示就是一位一位地轮流点亮各位数码管，对于每一位LED数码管来说，每隔一段时间点亮一次，利用人眼的“视觉暂留"效应，采用循环扫描的方式，分时轮流选通各数码管的公共端，使数码管轮流导通显示。-Based on 51 single-chip LED digital tube dynamic display, LED digital tube dynamic display is a bit lit Members take turns digit
led
- ISE开发软件、spartan3e开发板，左右两个按键控制8个发光二极管的左右移动点亮-Eight light-emitting diode the ISE development software, spartan3e, development board, around two button control and move around lit
LED
- 利用AT89C52点亮一个LED，是入门单片机位操作的基础。-AT89C52 light a LED entry MCU-bit operating foundation.
four-LED
- 4个LED灯跑马灯方式循环点亮 方式：先1个灯点亮，再2个灯点亮，3个灯点亮，4个全亮。-Marquee way cycle of four LED lights lit the way: first, a lamp is lit, then two lamp lights, three lights lit four full brightness.
LED(point)
- 通过51单片机的控制，利用指针的方式实现LED的点亮-51 MCU control, do while statement function LED lit
STM32_TIM
- 利用STM32F103xx芯片中的TIM3定时器点亮LED灯-Utilize the the STM32F103xx chip TIM3 timer lit LED lights
IRQ
- s3c2440开发板中断处理程序(RealView MDK),RealView MDK 4.60下的非常简单的中断处理程序，按键点亮LED灯。-s3c2440 development board interrupt handler (RealView MDK) RealView MDK 4.60 very simple interrupt handler, the button is lit LED lights.