搜索资源列表
wendu
- LPC1114+热敏电阻+数码管,检测温度,打到设定的报警值时蜂鸣器工作。左右键切换华氏摄氏,上下键改变报警值。(LPC1114+ thermistor + digital tube, check the temperature, hit the set alarm value, buzzer work. Key switch about Fahrenheit Celsius, up and down key to change the alarm value.)
NTC100K温度计程序
- 使用单片机的ADC功能来测温,利用共阴数码管显示(The use of single-chip ADC function to measure temperature, the use of a total of Yin digital display)
STC15W408ASHC595驱动数码管
- 基于100K NTC的测温程序,利用ADC引脚来检测电压并推算出温度,利用74HC595驱动 ----显示。(Based on 100K NTC temperature measurement procedures, the use of ADC pin to detect voltage and calculate the temperature, the use of 74HC595 driver display.)
NTCTempSample
- NTC热敏电阻通过ADC采样电压,查询厂家提供的阻值表,并通过插值计算,获取当前温度(NTC thermistor through the ADC sampling voltage, inquires the manufacturer to provide the resistance meter, and through interpolation calculation, obtain the current temperature)
MSP430温控器程序
- MSP430温控器程序,包括热敏电阻对应表 温度从1~40 估算测量温度,误差在1度以内(The MSP430 thermostat program, which includes thermal resistance corresponding to the temperature from 1~ 40, is within 1 degree)
基于51单片机的多路温度采集控制系统设计
- 本电路由89C51单片机温度传感器、模数转换器ADC0809、串入并出移位寄存器74LS164、数码管和LED显示电路等组成。由热敏电阻温度传感器测量环境温度,将其电压值送入ADC0809的IN0通道进行模数转换,转换所得的数字量由数据端D0-D7输出到89C51的P0口,经软件处理后将测量的温度值经单片机的RXD端串行输出到74LS164,经74LS164串并转换后,输出到数码管的7个显示段,用数字形式显示出当前的温度值(51 MCU multi-channel temperature acq
23. ADC NTC热敏电阻测量温度
- ntc,10k,15w4k,新手必备 亲测可用(Clear annotations can be used perfectly for the number of words)
B5
- 基于单片机和热敏电阻的室温监测装置的程序(Room temperature monitoring)
4-20ma RTD
- 可测量和处理来自 2 线、3 线和 4 线电阻式温度检测器的温度信号输入,并输出与来自 RTD 输入的所处理的温度相对应的 4 至 20 mA 电流回路信号,并进行系统级的校准以提高 ADC 和 DAC 精度。(It can measure and process the temperature signal input from the 2-wire, 3-wire and 4-wire resistive temperature detector, and output the 4-20 m
开源4个元件打造NTC10K温度计
- TC10k测温系统的硬件制作难度,我尽量优化设计,只需NTC热敏电阻+10k ......
用xpt2046采集AIN1的模拟信号-c51
- 用热敏电阻制作模拟信号,通过AIN1-通道1,YP+输入,X-驱动ON,Y-驱动OFF,可以精准采集并且输入到数码管上。由于xpt2046用24位时钟采集模拟量,通信时序很简单,所以我自己编写的,并由例程改进,注释详细。适合他人学习AD转换。
温度计的设计
- 热敏电阻器的典型特点是对温度敏感,不同的温度下表现出不同的电阻值。正温度系数热敏电阻器(PTC)在温度越高时电阻值越大,负温度系数热敏电阻器(NTC)在温度越高时电阻值越低,它们同属于半导体器件。随着半导体技术的不断发展,热敏电阻作为一种新型感温元件应用越来越广泛。他具有体积小、灵敏度高、重量轻、热惯性小、寿命长以及价格便宜等优点,最重要的是作为温度传感器的热敏电阻的灵敏度非常高,这是其他测温传感器所不能比拟的。
STM32F103读取NTC热敏电阻程序
- NTC采集温度的原理就是利用采样的ad值与对应表进行比较,得到温度值。温度与ad值的对应表可利用已经做好的表格来自动转化(输入参数,即可得到对应的ad值)