搜索资源列表
基于DSP56F805的交流电机驱动控制试验平台 .zip
- 基于DSP56F805的交流电机驱动控制试验平台 .zip
9直流电机
- 这是用CCS编写的DSP汇编程序，可以实现320TMSC54XXDSP与直流伺服电机定速控制实验 -CCS is used to prepare a compilation of DSP procedures, TMSC54XXDSP 320 can be achieved with the DC servo motor fixed speed control experiment
二相步进电机驱动芯片TA8435H控制
- 二相步进电机驱动芯片TA8435H及其应用-The control of Bipolar Stepper Motor of TA8435
电机转动控制实验
- ARM7 S3C44B0X 电机转动控制实验代码-ARM7 S3C44B0X motor rotation control experiment code
步进电机控制程序
- 一个控制步进电机的程序，用8051来控制步进电机-a program to control stepping motor, use 8051 to control stepping motor
永磁同步电机的Pwm波控制模型(推荐)
- 永磁同步电机的Pwm波控制模型(推荐)matlab仿真simulink仿真(PWM wave control model of PMSM (recommended) matlab simulation Simulink simulation)
永磁同步电机直接转矩控制和矢量控制仿真
- 永磁同步电机矢量控制和直接转矩控制仿真研究，数据已搭好，可以直接用(The simulation study of vector control and direct torque control of permanent magnet synchronous motor shows that the data are set up and can be used directly.)
无刷直流电机入门攻略
- 基STm32的电机控制程序开发教程以及无刷电机详细介绍(Development of Motor Control Program Based on STm32, Source Code and Related Tutorials)
LUNCHPADMSP430G2553L298电机驱动
- 能够驱动5v-12v直流电机电动小车的驱动不但要求电机驱动系统具有高转矩重量比、宽调速范围、 高可靠性，而且电机的转矩 -转速特性受电源功率的影响，这就要求驱动 具有尽可能宽的高效率区。(The drive of 5V-12V DC motor electric car requires not only the motor drive system with high torque-weight ratio, wide speed range and high reliability, but
拉力传感器电机控制
- 数据采集卡采集拉力值，与预先设定的拉力值进行比较，然后PID运算，控制相应的PWM占空比输出，最终控制电机的速度(The data acquisition card collects the pull value and compares it with the pre-set pull value. Then the PID arithmetic is used to control the output of the corresponding PWM duty cycle, and fin
pid控制永磁电机
- 基于matlab/simulink永磁同步电机的模糊PID控制仿真模型，适用于永磁同步电机，仿真效果还可以(The fuzzy PID control simulation model based on MATLAB / Simulink is suitable for PMSM, and the simulation effect can also be)
自适应的永磁同步电机
- 基于MRAS模型参考自适应的永磁同步电机PMSM在线参数辨识MATLAB仿真模型，可辨识电机定子电阻、电感和永磁磁链，辨识精度比较高。(Based on the MRAS model reference adaptive PMSM on-line parameter identification matlab simulation model, the stator resistance, inductance and permanent flux can be identified, and
多电平逆变器异步电机矢量控制模型
- 本程序为多电平逆变器异步电机矢量控制模型(This program is a vector control model of induction motor with multilevel inverter)
电机控制原理图
- 基于STM32F407ZGT6，PWM电机驱动及控制，集成MPU6050，预留蓝牙接口(Based on stm32f407zgt6, PWM motor drive and control, integrated mpu6050, reserved Bluetooth interface)
STM103步进电机控制
- STM103VCT6实现多轴步进电机控制(Stm103vct6 realizes multi axis stepping motor control)
电机
- 基于EKF的三相PMSM无传感器矢量控制框图，EKF算法采用s函数进行编写，函数命名为EKF。其中，输入为电机在静止坐标系下的钉子电压和定子电流，输出为定子电流估计值，转速和转子位置(Based on EKF's three-phase PMSM sensorless vector control block diagram, EKF algorithm uses s function to write, and the function is named EKF. Among them, th
简易步进电机S加减速
- 步进电机的加减速算法，内容非常详细，注释也比较清晰(Acceleration and deceleration algorithm of stepping motor)
PID电机位置控制v2.0
- PID电机位置控制源码—库函数版本STM32程序(PID motor position control source - library function version)
步进电机驱动器测试例程
- 基于stm32开发板的步进电机的控制程序源码(the control of motor base on stm32)
电机自抗扰控制和PID控制
- 电机的PI控制系统和非线性自抗扰控制系统的仿真程序。从仿真结果可以看出，线性自抗扰控制器和非线性自抗扰控制器一样，具有良好的动静态性能，(Simulation program of PI control system and nonlinear active disturbance rejection control system of motor. The simulation results show that the linear ADRC has good dynamic and sta