搜索资源列表
红外遥控接收
- 红外遥控接收 ORG 0000H LJMP START 转入主程序 ORG 0010H START: MAIN: JNB P2.2,IR LJMP MAIN 以下为进入P3.2脚外部中断子程序，也就是解码程序 IR: MOV R6,#9 SB: ACALL DELAY882 调用882微秒延时子程序 JB P2.2,EXIT 延时882微秒后判断P3.2脚是否出现高电平如果有就退出解码程序
遥控接收
- 单片机6502 编程实现红外遥控接收-6502 microcontroller programming infrared remote control receiver
红外发射接收程序
- 通用红外遥控系统由发射和接收两大部分组成，应用编/解码专用集成电路芯片来进行控制操作
IR_RECEIVE.rar
- C51写的红外遥控接收程序，遥控码规范为NEC规格。,C51 written procedures for receiving infrared remote control, remote control for the NEC code requirements specification.
yaokong
- 基于atmega16的红外遥控接收程序，用c语言写的，经检验的。-Based on the infrared remote control receiver atmega16 procedures, using c language written by the test.
infared
- 才用C语言编写单片机程序，实现了红外遥控接收。把接收到的数据通过LCD1602显示，并通过串口发送，方便查看。有很详细的注解，便于理解！-Only single-chip using C language program, the realization of the infrared remote control receiver. To receive data through the LCD1602 display and through the serial port to send,
remotept2221
- 红外遥控接收程序，PT2221,很简洁已经成熟使用-Infrared Remote Control Receiver procedures, PT2221, very simple and has been the use of sophisticated
Remote_Pro
- 实用红外遥控接收，解码程序。已经通过调试。-Practical infrared remote control receiver, decoding procedures. Have passed testing.
infrared_remote
- 本源程序是基于AT89C52单片机的红外遥控接收和发送源程序。对于初学者有很好的参考价值。-The source is based on AT89C52 microcontroller to receive and send infrared remote source. For beginners there is a very good reference value.
51code
- 51开发板上的源代码程序，里面有DS18B20液晶1602显示温度和控制代码，lcd1602时间显示c 程序代码，lcd 1602液晶显示代码，lcd12864字库显示代码，24C02存储器I2C总线代码，还有红外遥控接收和读码代码。-51 the development of on-board procedures for the source code, there are DS18B20 LCD temperature display and control the 1602 code,
C51接收32BIT—IR
- 利用51定时器中断为125US接收NEC红外遥控接收，并且接收完毕作处理。(With 51 timer interrupts, the NEC infrared remote receiver was received by the 125US, and the processing was received.)
PIC红外接收程序
- 红外线遥控接收程序，接收的是一个电视遥控器编码，共25个按锓 20140727经过调试，可以正常收码;收到的码按从高到低，存放在rx3,rx2,rx1,rx0四个寄存器中。(Infrared remote control receiver program, receiving is a TV remote encoding, a total of 25 to 20140727 Qin after debugging, can normally receive code; the code a
基于单片机的红外遥控门禁系统
- 基于单片机的红外遥控门禁系统(具有键盘输入模块，红外接收模块，液晶显示模块）(Infrared remote control door control system based on single chip microcomputer)
hongwai2
- 红外遥控接收，1383一体化红外接收头，AVR主芯片(Infrared remote control reception, 1383 integrated infrared receiver, AVR main chip.)
FPGA_红外遥控系统设计
- 上电后我们的设计会发一次我们给定的数据码，然后在接受模块会接受到其发送的数据并在数码管上显示出来,之后我们可以用我们我的遥控键盘来发送数据,接收模块接收显示出来.(After power up, our design will send a given data code, then the receiving module will accept the data that it sends and display it on the digital tube. Then we can use
实验18 红外遥控点亮LED
- 使用89C51作为控制芯片，使用红外遥控接收模块，控制C51的一个IO口点亮LED灯(Using 89C51 as the control chip, the infrared remote control receiving module is used to control a IO port of C51 to light the LED lamp.)
11-红外遥控接收程序
- 红外遥控接收程序，采用的是C和汇编两种语言的源码(infrared remote control)
20-红外遥控同时发射接收程序
- 红外遥控同时发送接收程序u，内含C和汇编两种语言(Infrared remote control simultaneous sending and receiving program u, containing C and assembler two languages)
28. 红外遥控实验
- 红外遥控器发射红外键值的编码信号，通过红外接收头进行解码，并将解码后的数据通过串口打印(Infrared remote controller emits a coded signal of infrared key value, decodes it through an infrared receiver, and prints the decoded data through a serial port.)
15 红外遥控收发仿真
- 用proteus仿真红外接收，发射，已成功。(Proteus simulation of infrared receiving, launching, has been successful.)