搜索资源列表
MAIN
- 一种QPSK调制解调算法的误码率仿真-a simulation of demodulation with Qpsk.
uwbbpsk
- 用matlab编辑的关于超宽带通信的BPSK调制的误码率分析,系统仿真时加入高斯白噪声,仿真结果给出了时域和频域图-BER analysis of the ultra wide bank BPSK communication channel with AWGN, time and spectrum figures are given in the end.
bpsk_ask
- 分析了ASK和BPSK通信系统,接收机采用相关器接收分析系统测试和理论误码率-Analyzed ASK and the BPSK communications system, the receiver uses the correlation instrument receive analysis system test and the theory error rate
cdmabpskMul
- 描述DSCDMA多用户系统在AWGN信道下的误码率-Describes the DSCDMA multiuser system under error rate of the AWGN channel
bpsk1
- 利用matlab对BPSK系统的误码率进行仿真,解压无需密码-use matlab to realize the BER of BPSK and it needn t password for extract the file
simu
- DS-UWB的仿真框图,误码率仿真,脉冲发生器,ook和bpsk调制,以及rake接收等-the simulation graph of DS-UWB,it includes the BER and pulse generation,ook and bpsk modulation and rake receiver.
mimo
- 一个4*8天线数的mimo仿真程序,采用16QAM调制解调,在平坦衰落环境下的误码率情况-a 4 * 8 the number of MIMO antenna simulation program using 16QAM modulation and demodulation, the decline in flat environment of the BER
eccnew
- 该程序可以算出未经编码和编码后的误码率,从而很清楚的表现纠错编码后系统的改善.-the program can be calculated without coding and the coding error rate, the performance is very clear after the error-correcting coding system improvements.
rsencode
- 通过编程计算RS编码前后通信系统的误码率可以很清楚的看到系统的编码增益.-programmed to calculate RS coding communication systems around the BER can clearly see the coding gain.
qpsk_rayleigh&awgn_ber&powerspec
- qpsk调制在awgn/rayleigh信道下的误码性能比较,以及信号的功率谱和星座图-QPSK modulation in awgn / Rayleigh Channel Performance Comparison of error, and the signal power spectrum and constellation
CDMA跳频通信子程序
- CDMA跳频通信子程序,本子程序计算CDMA跳频通信的误码率-CDMA frequency-hopping communications subroutine, the book calculation procedures CDMA frequency-hopping communications BER
16apsk
- 16apsk信噪比与误码率的关系曲线 星座图(Constellation diagram of the relationship between signal-to-noise ratio (SNR) and bit error rate (BER) of 16APSK)
qpsk
- qpsk调制,解调,通过高斯信道误码率计算,并画误码率图和眼图,星座图(QPSK modulation, demodulation, error rate calculation through Gaussian channel and drawing error rate diagram and eye diagram. constellation diagram)
turbo_code_tufa - 副本
- turbo码在MATLAB仿真中具体的实现模型并画出了不同情况下的误码率曲线(The realization model of Turbo code in MATLAB simulation and the error rate curves under different conditions are drawn)
信噪比-误比特率曲线
- 使用Labview平台计算误码率,绘制误码率曲线,用于通信系统仿真。(Calculate the bit error rate and reconstruct the bit error rate curve)
qpsk和16qam在高斯和瑞利分布下的误码率分析
- qpsk和16qam在高斯和瑞利分布下的误码率分析,内附分析和源代码
ook调制
- 自由空间中无线光通信系统使用OOK调制的误码率,源代码可直接运行(Bit error rate of free space optical communication system using ook modulation)
基于特殊训练序列的蒙特卡洛信道估计与误码率仿真
- 基于特殊训练序列的蒙特卡洛信道估计与误码率仿真(含h_decimation.am文件) 本文档仅供学习交流之用,禁止用于商业用途!违者责任自负!!!(Monte carlo channel estimation and bit error rate simulation based on special training sequence (including h_decimation. Am file) This document is for learning and communicati
基于高斯白噪声信道BPSK调制下的误码率与信噪比的关系
- MATLAB代码 公式推导的时候信噪比的单位是B,目的是为了推导的方便,代码在写的时候需要记得换算。 单个符号的比特数跟信噪比有关,snr越大,其越大。 由于符号1被误认为是0的概率与符号0被误认为是1的概率是一样的,因此无论蒙特卡洛的仿真次数是多少,误码率的理论计算值 与蒙特卡洛仿真值永远一样!(条件是高斯白噪声为0均值的) 为了让实际结果与理论值完全一样,高斯白噪声的概率密度函数中的均值需要为0!但是这个条件在实际生活中无法满足。 环境是不能改变的,因此噪声的均值是无法改变的。
16QAM在AWGN信道下误码率和误比特率比较
- 16QAM在AWGN信道下误码率和误比特率比较